Make a Moxon Vise
- Laminate Wood. If you have 8/4" Stock you can skip this step. But I only had 4/4" stock and many people do. ...
- Dimension the Chops. Now that you have two thick slabs we need to bring them down to dimension.
- Cut Hold Fast Holds. In the Back Chop start by drilling a 1" hole that is centered 2 1/2" into either end of the chop and up 1 ...
- Shape the Chops. The front chop needs a deep 45-degree chamfer along the top front edge. I leave 1/2" on the top that is flat.
- Bore Holes for Screws. You will need to choose a bit the t fits your wood screw tap. Mine was 13/16". ...
- Shape Screw Nuts. You can shape these any way you wanted. ...
- Tap the Nuts and Chop. In the nuts, use the same bit used on the back chop to drill a hole through the center of the nut. ...
- Cut the Screw. Use the thread cutting box to cut the screw end to end. as before this can be easier if you oil the smooth dowel beforehand.
- Glue Nut and Bolt. Apply a bit of glue to the inside of the nut and one end of the threaded rod. ...
- Finnish and Use. Use Boiled Linseed Oil and Paste wax to finish the wood pieces. here is a video on that finish procedure. ...
Full Answer
Can You Make your own Moxon vise?
The Moxon Vise hardware kit comes with an instruction booklet with everything you need to know to make your own Moxon Vise. You can customize it based on your height or what kind of wood you have. The options are endless, but I will share the dimensions I decided to go with….
How do you fix the sliders under a Moxon vise?
Install the Sliders Wong used pan-head screws to lightly fix the wooden sliders under his bench, centered on his moxon vise. They remain under the bench, out of the way, until needed. (Photos by Chris Wong)
How do you set up a stock vise?
The vise is quick and easy to set up and holds stock securely in place. Plus it’s a great conversation piece. Steps Mill the stock to finished dimensions. Clamp jaws together; mark out the jaw holes; drill the rod holes. Chop out the mortises for the nuts on the back of the fixed jaw.
What are the parts of a vise?
The Vise is made up of 2 parts, a front jaw and a rear jaw. The front jaw should be between 3/4” and 1-1/2” thick, 23-1/2” long and at least 4” tall. The rear jaw should be at least 1-1/2” thick, 29-1/2” long and at least 4” tall.
What wood should I use for a Moxon Vise?
2) When building the wood jaws for the moxon vise, which wood should I use? Walnut is my favorite species, but most of these I see are either southern yellow pine, cherry, or maple.
How do you make a Moxon vice?
0:0815:06$40 Moxon Vise - Easy to build in an afternoon! - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis kit comes with everything that you need to build a quality Moxon vise it also comes with a setMoreThis kit comes with everything that you need to build a quality Moxon vise it also comes with a set of instructions.
How thick should a Moxon Vise be?
The Vise is made up of 2 parts, a front jaw and a rear jaw. The front jaw should be between 3/4” and 1-1/2” thick, 23-1/2” long and at least 4” tall. The rear jaw should be at least 1-1/2” thick, 29-1/2” long and at least 4” tall. What is this?
How does a Moxon Vise work?
The Moxon vice is fitted with cast iron hand wheels for rapid, easy adjustment. Instead of the handwheel rotating the screws and being restricted by the weight of the movable jaw, BENCHCRAFTED tapped the handwheels, allowing them to move in and out on the rigid screws.
How do you make a pipe clamp vise?
0:159:22Pipe Clamp Workbench Vise - 210 - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut instead of making something very similar to it to sit on top I want to make a twin pipe clampMoreBut instead of making something very similar to it to sit on top I want to make a twin pipe clamp style bench vise to go on the end of this particular work table just like the previous vise.
How do you build a leg vise?
3:554:59Build a Workbench Leg Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipI cut one half down to make it a smaller 12 inch wedge for work pieces up to three inch wide. I thenMoreI cut one half down to make it a smaller 12 inch wedge for work pieces up to three inch wide. I then use the wedge to mark off the corresponding. Piece that I needed to remove on the chop.
How do you attach a Moxon Vise workbench?
0:034:06Moxon vice in a workbench - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's installed with bolts one one side one the other and then these lovely wheels just spin freelyMoreIt's installed with bolts one one side one the other and then these lovely wheels just spin freely allowing the jaws to go back. And forwards. It's great for dovetailing.
How do you make a woodworking vise?
0:117:17How to make a Workbench Vise ( DIY MOXON VISE ) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe radius jig definitely made this a little easier and more accurate. But you can totally use a jigMoreThe radius jig definitely made this a little easier and more accurate. But you can totally use a jig saw to round this over. On one side of the jaw. I need to round out a dado slab.
How do you make a portable vise?
0:271:27How to make your bench vice portable - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow that you've drilled the holes you're going to turn the board over and Mark out the top of theMoreNow that you've drilled the holes you're going to turn the board over and Mark out the top of the bolts. So now you want to chisel out like this so the ball is sits under the surface.
How do you make a Moxon antenna?
2:4642:37Smitty Working On SOMETHING: 20m Moxon Antenna build project, Part 1.YouTubeStart of suggested clipEnd of suggested clipSupport in the middle and one of the common ways of doing that is to getting getting an inexpensiveMoreSupport in the middle and one of the common ways of doing that is to getting getting an inexpensive plastic cutting board like this one here and then drilling the holes in it.
How does a wagon vise work?
8:149:07$24 Wagon Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipReally really well the main point of a wagon vise is to be able to clamp laterally. On the ends ofMoreReally really well the main point of a wagon vise is to be able to clamp laterally. On the ends of the boards.
How do you attach a Crubber?
Attaching Crubber You can use any glue you'd like to attach Crubber to your vise. We've used liquid hide glue, yellow carpenter's glue and contact cement. Contact cement is nice in that it likes to peel or rub off cleanly when it's time to replace the Crubber.
How do you make a workbench tail vise?
0:049:10I Built a Secret Tail Vise into my Workbench - YouTubeYouTubeStart of suggested clipEnd of suggested clipBuild this vise was made using an old linear actuator taken from my grandma's old lift chair whichMoreBuild this vise was made using an old linear actuator taken from my grandma's old lift chair which she was throwing. Out now this right here is the second linear actuator that i salvaged from that.
How do you attach a Crubber?
Attaching Crubber You can use any glue you'd like to attach Crubber to your vise. We've used liquid hide glue, yellow carpenter's glue and contact cement. Contact cement is nice in that it likes to peel or rub off cleanly when it's time to replace the Crubber.
How does a wagon vise work?
8:149:07$24 Wagon Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipReally really well the main point of a wagon vise is to be able to clamp laterally. On the ends ofMoreReally really well the main point of a wagon vise is to be able to clamp laterally. On the ends of the boards.
What is a Moxon Vise?
A Moxon Vise is an essential tool when you start working with hand tools. It clamps on to your workbench so you can cut joinery into the ends of your workpieces. When you’re done using it, you can take it off your bench and easily store it away!
How many parts does a vise have?
The Vise is made up of 2 parts, a front jaw and a rear jaw.
How tall should a vise be?
The height of the vise depends on how tall you are or how tall your workbench is. Anywhere from 4”-6” should work.
How to lock a rear jaw rod?
Keep threading the rod until it is protruding out the back of the rear jaw and lock it down with a washer and another nut.
How to mark a front jaw?
On the front jaw, mark 1/4” from either side of the 2-3/8” marks. This will create an oval hole that will allow the front jaw to pivot so you can clamp angled or tapered parts. This is what the marks on the front jaw should look like: 1 line marking the center of the board (the horizontal line below).
How much space between rods when cutting?
Cutting the front jaw at 23- 1/2” will leave a gap of 18” between the rods, which is plenty of space to work with.
Where do I cut a bevel on a dovetail?
I cut a bevel on the top front face of the front jaw. This is so that I could use a handsaw for cutting things like half blind dovetails without the jaw getting in the way.
How thick should a vise be?
For a sufficiently stiff vise, you'll want to make sure your material is 1.5" - 1.75" thick. I decide to glue up multiple boards for my vise. This not only added a pleasant visual design, it also should help to hold its shape better and costs significantly less than solid wood. Once the pieces were glued, I trimmed the edges down to final dimension.
How many coats of tung oil for vise?
Everything was sanded to 220 prior to assembly so finish prep was minimal. I gave all pieces of the vise 3 coats of Tung Oil for protection before final assembly. Assembly is straight forward and it's nice to see the whole thing come together at last!
How to cut a mortise for a nut?
Use a chisel to chop out the mortise for the nut. Test fit multiple times until nut sits flush with the top of the chop.
How to increase gripping power of chops?
Adding cork to the clamping side of both chops will increase the gripping power and protect the piece being clamped. I used adhesive backed drawer liner. Just line up your face on the unrolled cork, cut, stick the the jaw face, and trim to fit. Make sure the wood is clean and dust free.
What oil do you use to coat corks?
I coated all pieces with a Boiled Linseed Oil and Beeswax mix (making sure to not get any on the cork face).
Can you clamp a vise to a bench?
You be able to clamp the vise to your bench, you'll want to add a small board a little longer than your vise to act as a clamping surface. I used a piece of southern yellow pine attached with three brass screws to the back side of the rear chop. I used a hand drill to pre-drill all of the holes before attaching.