How do you identify a leg vice?
2:384:57Identifying blacksmith leg vise material, wrought iron, steel, etc - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe bottom left is the cast iron swage block and the bottom right is the high carbon steel.MoreThe bottom left is the cast iron swage block and the bottom right is the high carbon steel.
What is a leg vice made of?
Leg Vices were traditionally made from Wrought Iron and are still Forged in steel.
What is a post leg vise?
A blacksmith's post vise or "leg vise" is designed to be hammered on, unlike most bench-mounted machinist vises. The long leg transmits the energy from hammer blows all the way from the massive fixed jaw to the floor. Hot iron is secured in the vise and then shaped as needed by hammer blows.
What is a blacksmith vise?
0:1010:04Vises for the blacksmith shop - tool of the day - YouTubeYouTubeStart of suggested clipEnd of suggested clipLike it does in a modern machinists vise the jaws are actually loose. And it's just a spring thatMoreLike it does in a modern machinists vise the jaws are actually loose. And it's just a spring that the heat makes it feel tight. But the jaw can move and wiggle a little bit. Because all of the weight.
What is the best material for a vice?
Steel. Steel is an alloy of iron and carbon. It is a material widely used in construction due to its tensile strength and high corrosion resistance. The jaw surfaces, handle, and screw of a vice are usually all made of hardened steel.
What are the types of vice?
There are the following types of vices used in the workshop: Bench Vice. Pipe Vice. Tool Makers Vice.
How do you do a post vise stand?
4:316:10Making A Post Vice Stand - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd use some m8 coat screws to hold it in place. With all four screws in place and get the post toMoreAnd use some m8 coat screws to hold it in place. With all four screws in place and get the post to the vise put into that bracket. Then that mounting plate gets slid into the vise itself.
How do I mount a post vice?
0:546:54Building the ULTIMATE Post Vise Stand| Iron Wolf Industrial - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the first thing that we need to do is figure out if the leg of our post slice can be fit up inMoreSo the first thing that we need to do is figure out if the leg of our post slice can be fit up in one of these. Holes. So once you have your holes. Cut out enough to where the toast of us can fit.
What is a blacksmith swage block?
A swage block (or swager block) is a large, heavy block of cast iron or steel used in smithing, with variously-sized holes in its face and usually with forms on the sides.
How do you mount a leg vise?
0:577:00Installing a Leg Vise on a Workbench - 253 - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe don't necessarily need to shim the entire base to match the overhang. Instead we're going to addMoreWe don't necessarily need to shim the entire base to match the overhang. Instead we're going to add a front jaw to the vise. And to do so we need to remove just a little bit of material.
How do you build a leg vise?
3:554:59Build a Workbench Leg Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipI cut one half down to make it a smaller 12 inch wedge for work pieces up to three inch wide. I thenMoreI cut one half down to make it a smaller 12 inch wedge for work pieces up to three inch wide. I then use the wedge to mark off the corresponding. Piece that I needed to remove on the chop.
How do you make a bench stand vise?
0:3612:55Building a Simple & Cheap Vise Stand - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can do this really cheap really simple. The basic materials that we're going to use for our viseMoreYou can do this really cheap really simple. The basic materials that we're going to use for our vise Stan. There's going to be one two by four and two two by eight all eight feet long.
How do you build a leg vise?
3:554:59Build a Workbench Leg Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipI cut one half down to make it a smaller 12 inch wedge for work pieces up to three inch wide. I thenMoreI cut one half down to make it a smaller 12 inch wedge for work pieces up to three inch wide. I then use the wedge to mark off the corresponding. Piece that I needed to remove on the chop.
How does a leg vice work?
3:114:58What Is That Board With All the Holes | Wooden Leg Vise Pinboard ...YouTubeStart of suggested clipEnd of suggested clipThe other great benefit to a leg vise is you can actually use the leg itself to support the work andMoreThe other great benefit to a leg vise is you can actually use the leg itself to support the work and here I've taken a pin out and I'm allowing the work to stick down past the screw. So now the work
What is the material of bench vice?
An engineer's vise, also known as a metalworking vise, machinist's vise, or, informally, a "bench vise", is used to clamp metal instead of wood. It is used to hold metal when filing or cutting. It is sometimes made of cast steel or malleable cast iron, but most are made of cast iron.
What is the function of the leg on the vice?
What makes a leg vice special? One is that they are forgings, not cast iron or ductile iron. The second is the leg which provides support to the floor or from a sunken post. The leaf spring is a critical part of the vice, as it enables you to work quickly when securing your work.