Identifying Vises by Production Dates Some antique vises have dates on their slide keys, if you haven’t noticed. A good example is an old vise from Wilton. These numbers tell when the tool was ready for release or sale. The vise’s body contains the sliding key, which prevents the front jaw from rotating.
What do the numbers on a vise mean?
A good example is an old vise from Wilton. These numbers tell when the tool was ready for release or sale. The vise’s body contains the sliding key, which prevents the front jaw from rotating. It is a square piece of key stock that fits into the vise’s grooves. To locate the sliding key, simply unscrew it completely and turn it over.
How to identify an antique vise?
Identifying an Antique vise is very easy. Though modern and older versions have the same basic features, there are a few distinctions between both. Here are the basics that differentiate an antique from the current tool versions. The first and foremost thing that distinguishes an antique is its material.
Where can I buy a good vise?
Most folks have access to a Home Depot, or Lowes, so I’m going to pick vises they normally carry in the store so you can go see one in person. Home Depot offers a Bessey 6″ vise on a swivel base that weighs 44lbs.
How high should a vise be mounted?
In many cases people buy or build dedicated stands that bolt to the floor, or build a short bench just for the vise to put it at the right work height. In the pictures above, the 5″ vise is 10″ tall and the 6″ next to it would be 12″ if it was mounted on a swivel base.
How do you indicate a vise in Bridgeport?
1:273:11Indicate the vise on a milling machine in just one pass - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you don't have one of the mounts you can just put the indicator in your drill chuck or in aMoreIf you don't have one of the mounts you can just put the indicator in your drill chuck or in a collet however you want to do it. And line the indicator up with the right.
When indicating a vise on the mill which jaw should you indicate and why?
Always indicate the hard jaw side of the vise close to the pivot point and with no more than one revolution, jog the table in the “Y” axis to bring the indicator to zero.
How do you true a vise?
3:115:42Machine Shop Basics: Setting up a Vise on a Milling Machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipUntil it gets to zero. And again I have my vise just loosely tightened on the table it is tight. ButMoreUntil it gets to zero. And again I have my vise just loosely tightened on the table it is tight. But not so tight that I can't bump it around. But it is fairly tight and tight on there.
How do you align a vise on a mill?
0:018:03How to align a milling machine vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe vise on a vertical mill. We want to make sure that this fixed jaw this is the fixed jaw this isMoreThe vise on a vertical mill. We want to make sure that this fixed jaw this is the fixed jaw this is a movable jaw the movable jaw has just a little bit of play in it so we don't want to try to align.
How do you clock a vice?
2:4511:08Clocking or dialling in a vice to the milling machine. - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd i'm going to just wind it until it goes up to the zero notice actually we are nearly halfwayMoreAnd i'm going to just wind it until it goes up to the zero notice actually we are nearly halfway along the travel of the dti in this instance by the position of the small needle on the clock.
How do you indicate a mill head?
Dial indicating around the mill head X-axis.With the dial zeroed and the spindle in neutral, rotate the spindle so that the dial indicator is now on the front of the table, ideally a 180 degree turn. ... Note the direction that the dial rotates to determine the direction that the mill head needs to travel.
How do you indicate a part in CNC mill?
1:1310:01Indicating the Center of a Hole for Proper CNC Machining - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe tool holder the body of the indicator stays stationary. So this is nice because then you canMoreThe tool holder the body of the indicator stays stationary. So this is nice because then you can sweep the indicator needle around the bore. And you can always see the gauge. Face on the indicator.
How do you square a Bridgeport mill?
5:4913:49How to square the Bridgeport head with the table - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I like to keep the point of the indicator somewhere in that area. So we'll bring this spindle.MoreAnd I like to keep the point of the indicator somewhere in that area. So we'll bring this spindle. Down we'll touch it. And let's put our zero right here let's say. And we'll start with our sweep.
How can a vise be checked for squareness?
Feed the dial test indicator back to the left side of the vise. The dial should stay at or around zero for the whole duration. Pits and burrs on the face of the mill will show up as low and high spots, but you shouldn't see any tendency to increase or decrease.
How can workpieces be aligned when they are clamped to the table?
0:3410:18Advanced manufacturing - Dial In a Vice on a Milling Machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipFive thousand five ten thousands each big lines a thousand. So I'm going to put this into theMoreFive thousand five ten thousands each big lines a thousand. So I'm going to put this into the spindle. And use it against the back edge of the vise to dial it in so I'm going to be in hand jog.Advanced manufacturing - Dial In a Vice on a Milling Machine - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you dial in a machine vice?
What is machine vice?
How should an operator align a vise when using it as a workholding device? An operator should align a vice along the: NOT Y axis with the column. What type of milling feeds the workpiece against cutting tool rotation?asdadfasfasdfasdfasfas Flashcards - Quizlethttps://quizlet.com › asdadfasfasdfasdfasfas-flash-cardshttps://quizlet.com › asdadfasfasdfasdfasfas-flash-cardsSearch for: When setting up a vise How should operators position the vise for proper alignment operators should align the?
What is milling in engineering?
Work pieces can be aligned on a machine table by measuring their distance from the edge of the table, by locating against stops in the T-slots, or by indicating the work piece side.