Here are the 7 steps involved in mounting a 10″ Yost front vise to your workbench:
- Disassemble it to understand how it works
- Mark the position on your workbench and drill out the holes
- Cut and prepare hardwood panels as the clamp face
- Mount and screw the woodworking vise onto your workbench
- Plane the vise top flush with your workbench top & apply a finish
Full Answer
How to install a woodworking vise?
How to Install a Woodworking Vise. 1 Step 1: Measure for Your Jaw (s) Clamp the vise and plate where you want the vise to be installed. Get a rough measurement of the vise jaw while the ... 2 Step 2: Cut Out the Rough Sized Jaw (s) 3 Step 3: Remove the Vise From the Clamps. 4 Step 4: Remove Back Plate. 5 Step 5: Remove Quick Release Nut. More items
How do you mount a vise plate on a bench?
Pre drill all the marked locations and mount the plate with the proper sized screws for your vise. Place the jaw in posistion to be mounted, making sure to leave the top edge proud of the top of the bench. Use a pencil to mark the center of the holes in the vise mounting plate where the rods and screw will go through the front jaw.
How do you use a quick release vise?
If you are using a quick release vise, place the main screw and rods barely in the holes on the vise mounting plate (just enough to hold them in place. Reinstall the quick release nut ( in its proper orientation ) and screw the vise in. Reinstall the back plate onto the main screw and rods.
How do you close a vise modal on a workbench?
This modal can be closed by pressing the Escape key or activating the close button. A cast-iron woodworking vise is easy to install and a great addition to any bench. In this video, Ed Pirnik shows you how to mount one to your workbench, using a spacer block and a full length inside jaw apron.
How do you fit a front vice?
2:044:38How to install a Woodworking Vise// Woodworking// Quick Release ViseYouTubeStart of suggested clipEnd of suggested clipThen install the screws that will mount the front of the vise to the front jaw take quick-releaseMoreThen install the screws that will mount the front of the vise to the front jaw take quick-release vise you just barely want to put the screws in the guide rods in place so that you can situate.
How do you mount a vise?
0:075:05BENCH VISE - How To Install A Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipSide is close enough to an at the edge. Where if you have a long item that you're working on thatMoreSide is close enough to an at the edge. Where if you have a long item that you're working on that you need to clamp that it will clear. The side of the bench.
How do you mount under bench vise?
3:346:41Installing a Woodworking Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipThose will hold it up from the bottom inside these tabs I clamped the vise in place and used an awlMoreThose will hold it up from the bottom inside these tabs I clamped the vise in place and used an awl to poke holes where the screws will. Go.
How do you fit a vice to a workbench?
0:562:11How to Fix a Vice on a Workbench | Woodworking - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will need two nuts and washers to tighten the bolt. Fit the washer and then the nut below theMoreYou will need two nuts and washers to tighten the bolt. Fit the washer and then the nut below the table tighten it as much as you can with your hand. Use a spanner to tighten the nut below the table.
Where should I mount my vise?
2:3511:30How To Install A Vise Like A PRO - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you can put it on the corner. Something to consider that has really helped me I get it out as farMoreIf you can put it on the corner. Something to consider that has really helped me I get it out as far as I can it. Also is going to depend upon the vise.
How do you hang a vise without a bench?
7:3714:02How to mount a vise without drilling holes in your workbench - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow just just securing the very bottom lip of this bench because that's what it was that was theMoreNow just just securing the very bottom lip of this bench because that's what it was that was the whole purpose of this so i didn't have to drill into the into the workbench.
What do I attach a vice to?
0:061:57How To Properly Mount A Vice To Any Surface.. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I put a piece of wood on the top that's going to add some you know strength vise. It's going toMoreSo I put a piece of wood on the top that's going to add some you know strength vise. It's going to go right on top I already pre-drilled the holes. Bolts washer it's going to go right through.
Where should you put a vise on a workbench?
Bench vises hold better when you push toward them, with the mass of the bench behind the workpiece. That's why face vises usually are placed on the left end of the bench.
What is a face vise?
Face vises are designed specifically for holding wooden workpieces while such operations as drilling and sawing are performed. The traditional material is wood. A wood face vise consists of a movable front jaw that is mounted to a broad, square beam that slides in and out of a matching channel.
What clamping position should be considered when mounting a vise on a workbench?
What clamping position should be considered when mounting a vise on a workbench? The vise should be positioned so that a long piece can be held vertically in the jaws without interference from the workbench.
Where do you mount a vise to a workbench?
Bench vises hold better when you push toward them, with the mass of the bench behind the workpiece. That's why face vises usually are placed on the left end of the bench.
What size bolts to mount a vise?
Re: Mounting a Bench Vise Mine used 7/16 bolts to mount. Make sure to hang the jaws over the edge of the table, just as ware did. 7/16 seems to be right.
Where should a right-hander mount a vise?
Right-handers should mount a face vise at the far left of the bench’s front edge and an end vise on the end of the bench at the foremost right-hand corner. Southpaws will want to do the opposite. When retrofitting an existing bench, make sure the vise mechanism won’t interfere with the bench legs. Shift the top if necessary to accommodate the vise.
Where is the vise on a bench?
A vise’s location on the bench determines what it’s called. Face vises are attached on the front, or face, of the bench; end vises are installed on the end. The best benches have both, but if you can only afford one, I’d go for a face vise initially.
How big of a vise should I use for face planing?
Because a face vise is used for general work as well as for planing edges, I recommend investing in a larger vise (at least 10"). Since it’s primarily used in tandem with bench dogs to secure boards for face-planing, a smaller end vise should suffice.
How to attach a vise to a spacer block?
Use a straightedge to ensure the face of the jaw is flush with the edge of the ben ch. If it’s proud, level it with a hand plane.
How to measure spacer block thickness?
To determine the thickness of your spacer blocks, place the rear jaw upside down on the inverted benchtop and measure how much the top of the jaw projects beyond the underside. Add to that 1⁄4" for a 7" vise, or 1⁄2" for a 10" vise. (The former is necessary for better dog height on the smaller vise.)
How to make a cheek on a bench?
Make the front cheek, and attach it with washers and roundhead woodscrews, reassemble the vise, and turn the benchtop over. Hand-plane the cheeks flush with the benchtop (Photo H). My bench had radiused edges, so I chiseled away the sharp point at the corner of the cheek. Finally, apply a couple of coats of wipe-on finish to all raw wood surfaces.
How big is a face vise?
Because a face vise is used for general work as well as for planing edges, I recommend investing in a larger vise (at least 10"). Since it’s primarily used in tandem with bench dogs to secure boards for face-planing, a smaller end vise should suffice. I prefer a small (7") model, because its dog is only 31⁄2" from the front edge of the bench, which is convenient for clamping workpieces for face-planing and other operations.
Crosscut Sled for Large Panels
Steve Fikar's panel sled is guided by a single runner in one miter slot attached to a torsion-box base to keep the sled light.
Shop Talk Live Podcast
Our biweekly podcast allows editors, authors, and special guests to answer your woodworking questions and connect with the online woodworking community.
Step 3: Drill Bench
Drill holes to accommodate the vice screw and guide bars. Line up the mounting bracket to determine the location of the holes.
Step 6: Stationary Jaw
Push vice through the bench holes to line the stationary jaw up with the bench and fasten in place.