Installing a Quick Release End Vise
- Preparing Boards for the Jaws. The vise came with a nice wooden handle, but a pair of wooden jaws need to be built to match the workbench's depth ...
- Trimming Jaws to Final Width. After trimming off the snipe from one end of each board, I then marked off their final width and cut both together at ...
- Attaching the Inner Jaw. ...
Where should you mount a vise on a bench?
Right-handers should mount a face vise at the far left of the bench’s front edge and an end vise on the end of the bench at the foremost right-hand corner. Southpaws will want to do the opposite. When retrofitting an existing bench, make sure the vise mechanism won’t interfere with the bench legs. Shift the top if necessary to accommodate the vise.
How do you use a twinscrew vise on a bench?
The bench's apron, or a builtup end of the benchtop, serves as the inner jaw. A twinscrew vise has a large opening between the screws for holding wide stock or assembled drawers. Planing long boards held in the jaws can move the bench sideways. Instead, capture the workpiece with bench dogs to take advantage of the bench's full mass.
How to install a woodworking vise?
How to Install a Woodworking Vise. 1 Step 1: Measure for Your Jaw (s) Clamp the vise and plate where you want the vise to be installed. Get a rough measurement of the vise jaw while the ... 2 Step 2: Cut Out the Rough Sized Jaw (s) 3 Step 3: Remove the Vise From the Clamps. 4 Step 4: Remove Back Plate. 5 Step 5: Remove Quick Release Nut. More items
Can You retrofit a vise to an existing bench?
And high humidity could cause the parts to swell and bind. This vise does not easily retrofit to an existing bench. As the name implies, this vise installs into the bench leg, which sometimes serves as the fixed jaw. Build the outer jaw from thick stock about three-quarters of the leg's length.
How do you attach a vice to a workbench?
0:075:05BENCH VISE - How To Install A Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipSide is close enough to an at the edge. Where if you have a long item that you're working on thatMoreSide is close enough to an at the edge. Where if you have a long item that you're working on that you need to clamp that it will clear. The side of the bench.
How do you attach a woodworking vise to a workbench?
3:396:41Installing a Woodworking Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipI clamped the vise back in place and used an impact driver with a socket to drive the lag screws. InMoreI clamped the vise back in place and used an impact driver with a socket to drive the lag screws. In. The vise also gets secured on the front face through the jaw.
How do you mount a tail vice?
0:106:58How to Install a Tail Vise to your Workbench | HNT Gordon & Co.YouTubeStart of suggested clipEnd of suggested clipAnd you have to glue a piece of wood underneath where the position of the vise do that first glue.MoreAnd you have to glue a piece of wood underneath where the position of the vise do that first glue. And screw it let it dry. Then. The next thing you do is. If you have pre-existing dogs.
Where is the best place to put a vice on a workbench?
Bench vises hold better when you push toward them, with the mass of the bench behind the workpiece. That's why face vises usually are placed on the left end of the bench.
How do you mount a woodworking vise?
0:544:38How to install a Woodworking Vise// Woodworking// Quick Release ViseYouTubeStart of suggested clipEnd of suggested clipAs this will be very important later. Now you can use clamps to put the vise plate back in place useMoreAs this will be very important later. Now you can use clamps to put the vise plate back in place use a pencil to find the center of the holes. And then use a center punch to go ahead and mark them.
What clamping position should be considered when mounting a vise on a workbench?
What clamping position should be considered when mounting a vise on a workbench? The vise should be positioned so that a long piece can be held vertically in the jaws without interference from the workbench.
How do you use end vise?
9:4514:19Shop time: End Vise. - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd run into the Vice here. So it's very handy for just small little chamfers on the corners of workMoreAnd run into the Vice here. So it's very handy for just small little chamfers on the corners of work pieces. So I'll put a chamfer on here to prevent it from blowing out in just a second.
Do I need a tail vise?
The main reason why a traditional tail vise is so darn useful is because of the unobstructed gap you get in the front of your bench. this gives you the perfect way to solidly clamp chair legs, or any long part that needs to be held while you work on it from one end.
How does a tail vise work?
A tail vise's main purpose is to hold a board flat on the bench for planing, routing, sanding and so on. The tail vise pushes a board tightly against a bench dog so the board can't swivel or move. The bench dog fits in a series of holes cut in the top to accommodate different sizes of boards.
Why is the bench vise mounted on the edge of the work bench?
Mount a vise so that the stationary jaw projects slightly beyond the edge of the workbench. This allows long work to be clamped in the vise without interference from the edge of the workbench. Ensure that the workbench is firmly secured to its base.
How do you mount a vise toolbox?
1:113:26How to mount a bench vise to a Husky tool box - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat I did is I just hello marker marked down so now I'm gonna drill a couple holes three holes toMoreWhat I did is I just hello marker marked down so now I'm gonna drill a couple holes three holes to be exact. And I'm gonna go all the way through the wood to the top toolbox.
How do you hang a vise without a bench?
2:096:17Mounting a vise without taking up bench space. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you just go to the spot that it's at. And the holes are just a little bit loose so that they don'MoreSo you just go to the spot that it's at. And the holes are just a little bit loose so that they don't bind up.
How do you use a bench hook?
0:554:28How to Use a Bench Hook - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor a cross cut or shoulder cut you take the hook of your bench hook. And place it up against theMoreFor a cross cut or shoulder cut you take the hook of your bench hook. And place it up against the front edge of your workbench. Then you take your work. And place it up against the fence.
How does a quick release wood vise work?
0:401:54Introducing the Veritas Quick-Release and Inset Vises - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt features an extruded aluminum screw cover which keeps debris away from the screw mechanism andMoreIt features an extruded aluminum screw cover which keeps debris away from the screw mechanism and prevents the workpiece from touching the lubricated main screw.
How big of a vise should I use for face planing?
Because a face vise is used for general work as well as for planing edges, I recommend investing in a larger vise (at least 10"). Since it’s primarily used in tandem with bench dogs to secure boards for face-planing, a smaller end vise should suffice.
How to attach a vise to a spacer block?
Use a straightedge to ensure the face of the jaw is flush with the edge of the ben ch. If it’s proud, level it with a hand plane.
How to measure spacer block thickness?
To determine the thickness of your spacer blocks, place the rear jaw upside down on the inverted benchtop and measure how much the top of the jaw projects beyond the underside. Add to that 1⁄4" for a 7" vise, or 1⁄2" for a 10" vise. (The former is necessary for better dog height on the smaller vise.)
How to make a cheek on a bench?
Make the front cheek, and attach it with washers and roundhead woodscrews, reassemble the vise, and turn the benchtop over. Hand-plane the cheeks flush with the benchtop (Photo H). My bench had radiused edges, so I chiseled away the sharp point at the corner of the cheek. Finally, apply a couple of coats of wipe-on finish to all raw wood surfaces.
How big is a face vise?
Because a face vise is used for general work as well as for planing edges, I recommend investing in a larger vise (at least 10"). Since it’s primarily used in tandem with bench dogs to secure boards for face-planing, a smaller end vise should suffice. I prefer a small (7") model, because its dog is only 31⁄2" from the front edge of the bench, which is convenient for clamping workpieces for face-planing and other operations.
How to cut a notch in a bench?
Make the crosscut into the benchtop edge with a backsaw. Then clamp a straightedge to the bench to guide a circular saw to cut the length of the notch. Rip the notch until you intersect the previous crosscut (Photo C), and then finish up with a handsaw.
What is a workbench without vises?
Let’s face it; a workbench without vises is basically just an assembly table. Vises provide the muscle for securing workpieces for planing, sawing, routing, and other tooling operations. Of the myriad commercial models, the venerable Record vise is one that has stood the test of time, because it’s simple to install, easy to operate, and designed to survive generations of use. Although it’s no longer in production, several clones are available, including the Eclipse vise, which I show in this article. Similar vises may differ in features, but attachment is similar.
What is a vise for a bench?
With the help of a pair of wood, plastic, or metal bench dogs the vise makes it possible to quickly secure boards to the top of the bench for hand planing and can be used to hold small boards for edge planing and other sawing tasks.
How to engage quick release mechanism?
To engage the quick-release mechanism in this vise, you simply turn the handle counter-clockwise a 1/4 to 1/2 a turn and then slide the outer jaw in or out. Once the handle is turned clockwise , it will re-engage the quick-release mechanism which makes it possible to clamp down a workpiece.
How to attach inner jaw to work bench?
To make attaching the inner jaw to the bench easier, I took it to the drill press and made a few counter-bored mounting holes about an inch and a quarter from the top. Then at the workbench, I secured the jaw to the end by running a clamp across the edge of it and the bench top since I didn't have a clamp long enough to run down the length of the top. And after aligning the jaw, I pre-drilled and temporarily attached it to the top.
Can you balance rods inside the jaw?
This probably would have taken a bit less time with a helper, but it's possible to balance the rods a little inside the jaw and then hold the quick-release mechanism open so that the outer jaw can be slid into the vise.
Can you use a bench dog on a bench?
But since the outer jaw is quite tall, I found that using a short plastic bench dog there worked best.
Can you reinforce dado joints?
Allow the glue to cure. You could reinforce this dado joint with screws or dowels if you want, but with this much contact and the dimensional strength of the plywood, I think it'll stand up to any force I can apply with my hands. Also, at this point, I wiped on a coat of Danish Oil.
How long does it take to attach a bench dog to a bench?
This might be useful in the future if I'm cutting something quite long and need the side-to-side clearance and support in the middle. This took about 6 seconds.
What to do if you don't have a table saw?
If you don't have a table saw, you can do this with a circular saw or even a handsaw. Just make sure to mark a baseline, and keep everything secure.
Do I need to clean my Douglas fir blade?
Yes, I know I need to clean my blade. I've been cutting a lot of relatively fresh Douglas fir for a project, and the pitch has left a lot of build-up. I'll be following this tutorial soon!
Why is a shoulder vise used?
Because the outer jaw has a tongue that slides in a groove on the fixed arm, it has enough play to let you clamp uneven-shaped workpieces. A shoulder vise gives you floor-to-ceiling clamping space between its jaws. A threaded bushing mortised into the vise shoulder (unseen) keeps the screw on track. Things to know:
What is a pivoting jaw vise?
The benchtop’s edge or apron typically serves as the inner jaw. A pivoting-jaw vise holds irregular-shape stock without racking the jaws. You also can remove the pivoting jaw for parallel-jaw clamping. Magnet-lined wood jaw pads stay in place without screws. A cast-iron-jaw vise can be recessed into the bottom of a bench for maximum strength ...
What is bench vise?
Think of a bench vise as a tool that’s as essential to your success as a hand plane, router, or tablesaw. Although clamps might substitute in some situations, they tend to get in the way, and a vise gives you freedom to do almost any type of work.
How much does a metal vise cost?
Metalworking vises usually mount to the top of a bench. Woodworking vises vary in price from about $30 to as much as $400. Generally, once you decide on a particular style of vise, the more you spend, the better the quality and effectiveness of that vise. Now let’s take a look at the most common types of vises for woodworking.
What is a tail vise?
A traditional tail vise [ Photos H and I] consists of a rectangular or L-shape block of wood (the jaw) fastened to a steel or cast-iron fixture that slides back and forth in a cutaway corner of the bench.
Where do front vises mount?
Front vises. As the name implies, these mount to the front (long edge) of the bench, typically on a left-hand corner. Left-handed folks usually prefer a front vise mounted on the right corner.
Can wood dust cause respiratory problems?
Wood dust messes up a shop quickly and can lead to respiratory problems. Tablesaws with enclosed... read more
Can you take a vise off?
Now that you have your measurement and the jaw (s) cut, you can take the vise off.
Can you add an outer jaw to a vise?
So on my vise i chose to only add an outer jaw, and use the edge of the benchtop for my inner jaw but you can do this a couple different ways so do what works best for you! Cut the oversized jaw to length and width, but dont forget to leave a little extra so you can dial it in later.
Can you remove the quick release nut?
Remove quick release nut, but REMEMBER how it goes, i suggest taking a picture of it's oreintation so that you make sure it goes back correctly, if not the vise will not operate as intended.
What plane do I use to flatten a hard maple vise?
I then planed the top of the hard maple clamps flush with my workbench top and added bevels to the vise faces using my Stanley block plane. The No. 7 Stanley jointer plane works the best for flattening a large surface, but a No 5. Jack plane would do if that is what you have.
How many screws do I need to attach maple board to a table?
I attached the hard maple board to my tabletop with three screws. I pre-drilled each hole and counter-sunk them to recess the screws from the surface of the hard maple face.
How big is a vise handle?
You can turn a vise handle if you have a lathe. The actual inner diameter is just over 1″. Size your handle to 1″ and it should be just right.
How many holes are there in a vise?
Using the base of the vice and a sharp pencil, I traced out the three main holes for the vise from underneath. Since I traced inside the hole, I knew it would have to be slightly bigger in actual diameter.
How many nuts are in a guide rod?
The front portion will eventually separate, along with the two guide rods. There are two nuts and washers that hold the guide bars in place.
Can you close a vise?
I could now close the vise completely. Of course, better planning can help you avoid drilling through your table’s rails in the first place.
