Make a Bench Vise for Woodworking
- What You Need. About 16 linear feet of one by six hardwood (actual measurements ¾” x 5½”). ...
- Front Jaw. Cut two 32” long pieces from the one by six board. ...
- Rear Jaw. The rear jaw is L-shaped. The short ‘lip’ is used to clamp the rear jaw to your workbench. ...
- Drill Holes for the Hex Bolts. Drill two ½” holes through the front jaw 3” from the short edge and 2 ¼” from the top edge. ...
- Make Handles. You could stop right here and use ½” hex bolts and washers to complete the vise and open/close it with a wrench.
- Use Your Bench Vise. I did not use any finish on the bench vise or handles. I plan to sand it down if it needs cleaning. ...
Full Answer
How do you mount a vise to a benchtop?
For both styles, mount the inner jaw flush with the benchtop surface and edge (or apron), so that you can secure long workpieces in the vise and also clamp the board's far end to the bench for added stability. Your benchtop must clear the bench base or legs for mounting.
How do you use a twinscrew vise on a bench?
The bench's apron, or a builtup end of the benchtop, serves as the inner jaw. A twinscrew vise has a large opening between the screws for holding wide stock or assembled drawers. Planing long boards held in the jaws can move the bench sideways. Instead, capture the workpiece with bench dogs to take advantage of the bench's full mass.
Can You retrofit a vise to an existing bench?
And high humidity could cause the parts to swell and bind. This vise does not easily retrofit to an existing bench. As the name implies, this vise installs into the bench leg, which sometimes serves as the fixed jaw. Build the outer jaw from thick stock about three-quarters of the leg's length.
What is a bench vise used for?
Think of a bench vise as a tool that's as essential to your success as a hand plane, router, or tablesaw. Although clamps might substitute in some situations, they tend to get in the way, and a vise gives you freedom to do almost any type of work.
How do you make a bench vise?
0:147:17How to make a Workbench Vise ( DIY MOXON VISE ) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe radius jig definitely made this a little easier and more accurate. But you can totally use a jigMoreThe radius jig definitely made this a little easier and more accurate. But you can totally use a jig saw to round this over. On one side of the jaw. I need to round out a dado slab.
How do you make a woodworking bench vise?
0:306:39DIY Woodworking Bench Vise - Quick and Easy Shop Project - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo let's get. Started. Over at the table saw i cut a piece of 1 inch thick ash to 5 inches wide forMoreSo let's get. Started. Over at the table saw i cut a piece of 1 inch thick ash to 5 inches wide for the face of the vise.
What can I use instead of a bench vise?
Cut out this bird's mouth shape using whatever you have: a back saw, jig saw, coping saw, band saw. Set up the long piece of wood as a stop against the end your worksurface. If you're right handed, that's the left side; if you're a leftie, then the right side. Clamp or screw it in place.
What kind of wood is used for bench vices?
You can use plywood, a good grade, or solid wood, even pine, if that's what you have, to line the jaws of your vise. In this case I've chosen sapele, an african hardwood with perfect hardness and compression for this work. I've used it before and it's one of the best.
How do I make a portable bench vise?
0:271:27How to make your bench vice portable - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow that you've drilled the holes you're going to turn the board over and Mark out the top of theMoreNow that you've drilled the holes you're going to turn the board over and Mark out the top of the bolts. So now you want to chisel out like this so the ball is sits under the surface.
How do I make a quick release vise?
0:3017:20Homemade Quick Release Vice - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I've just cut into lengths and I've cut them at 500 mil. So my next job is to cut three holesMoreAnd I've just cut into lengths and I've cut them at 500 mil. So my next job is to cut three holes one either side for my guide rails where I'm using this tubing here off an old trampoline.
What are bench vises made of?
An engineer's vise, also known as a metalworking vise, machinist's vise, or, informally, a "bench vise", is used to clamp metal instead of wood. It is used to hold metal when filing or cutting. It is sometimes made of cast steel or malleable cast iron, but most are made of cast iron.
How do you hold wood vertically?
0:000:45Vertical Clamping - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you put the clamp in there. It's a great way to hold pieces in place vertically. And if you haveMoreIf you put the clamp in there. It's a great way to hold pieces in place vertically. And if you have a piece that needs a little support just clip in one of these included support brackets.
How do you hold something without a vise?
1:036:17How To Hold Your Work Without A Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you just take your piece of wood. And simply put the hold fast in the hole. And then you just sitMoreSo you just take your piece of wood. And simply put the hold fast in the hole. And then you just sit it on top. And you smack it down with a mallet.
How do you protect wood in a vise?
0:151:08How to Prevent a Workshop Vice from Damaging Wood - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust put it in place crank. It down I matter how much pressure you put on this. You're going to haveMoreJust put it in place crank. It down I matter how much pressure you put on this. You're going to have those pads in place.
How do you make wood vise jaws?
0:215:35Making New Vice Jaws - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's a hardwood. So it'll be nice and durable the jaws on my other vise they were just made fromMoreIt's a hardwood. So it'll be nice and durable the jaws on my other vise they were just made from some block board which is laminated pieces of pine with a veneer on both faces.
What wood should I use for a Moxon Vise?
2) When building the wood jaws for the moxon vise, which wood should I use? Walnut is my favorite species, but most of these I see are either southern yellow pine, cherry, or maple.
How do you make a Moxon Vise?
0:0815:06$40 Moxon Vise - Easy to build in an afternoon! - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis kit comes with everything that you need to build a quality Moxon vise it also comes with a setMoreThis kit comes with everything that you need to build a quality Moxon vise it also comes with a set of instructions.
How do you make a drill press vise?
3:539:44Homemade Drill Press Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipI cut the pins which are just wooden dowels down to their final size and tested the fit of theMoreI cut the pins which are just wooden dowels down to their final size and tested the fit of the backing on the base. After that I started laying out the rest of the components. I decided on pre
How do you make a vise clamp?
1:107:296 homemade clamps and workbench vises - YouTubeYouTubeStart of suggested clipEnd of suggested clipThese are just a couple of strips with two bolts. I put the work pieces between the strips. AndMoreThese are just a couple of strips with two bolts. I put the work pieces between the strips. And there are a lot of holes all along both strips.
Do it yourself work bench?
1:235:47DIY BUDGET FRIENDLY WORKBENCH (FREE ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce I cut the 4 legs. Then I cut 4 pieces of 2x4 at 69 inches to span the length of the bench. AndMoreOnce I cut the 4 legs. Then I cut 4 pieces of 2x4 at 69 inches to span the length of the bench. And four pieces at 24 inches to cap the ends of the bench with the pieces.
Step 1: Welding a Nut to a Base
I want to use a M16 threaded rod for the linear movement. Therefore I need a nut or something threaded to interact with the rod. I decided to weld a M16 nut to a flat plate connector. The flat plate connecter has already some holes to fix this part to the workbench. Unfortunately I don't have a welder so I asked my dad to do this job for me.
Step 2: Welding a T-Piece, a Washer and the Rod
I want to use a T-piece pipe to hold the threaded rod and a wooden rod later. The tee has two 3/4" ends and one 1/2" end.
Step 3: First Test Run
Both parts are finished. Let's try if everything fits together. Looks very good. The difficult part is done. Now comes some woodworking.
Step 4: The Moveable Jaw
So what we need next is a moveable jaw for the vise. My dimensions are 40cm by 15cm, but you can adjust them to your needs. I use scrap wood I have laying around. I would use some kind of hard wood for the jaws, but unfortunately I don't have enough, but I use a little trick.
Step 5: Mounting the Rod and the Support Pipes to the Jaw
I use two 5/8" copper pipes to support the rod and to keep the jaw from rotating. They have a length of 50cm. You can adjust the length to your needs.
Step 6: Drilling the Holes to the Workbench Jaw
This time I need three holes which go right through the workbench. I use my rack to get everything in a right angle. I finish the surface with a sander.
Step 7: Building the Flange
Remember the washer, which we welded to the T-piece? Now you'll see its purpose. I need some kind of flange, which will connect the jaw to the rod, but still loose enough to allow rotation. This allows the jaw to move with the rod while opening the vise.
Step 2: Open a Tube of CA Glue
My tube of superglue almost always glues its cap on itself, making it almost impossible to remove. Luckily, because CA is so fragile, when you squeeze the cap in a vise, it crumbles.
Step 3: Pry Open Electronic Devices
A vise is a great tool for prying open electronic devices, from phone chargers and computer mice, to flash-drives and TV remotes.
Step 4: Hold PCB's While Soldering
Before I built WAVE, I would hold big circuit boards in my vise. This would come in handy while trying to unsolder big components such as electrolytic capacitors and relays, but it wasn't really comfortable for soldering components on PCB's.
Step 5: How to Save Space- Clamp Tools in Your Vise!
One of my favorite uses for a vise is for clamping tools. Whether if you're using it to save space by making a mini portable router table, or using it to hold your sharpening stone, it's always extremely useful!
Step 6: How to Make an Improvised Drill-Press With a Vise
Since I have only two hands, it was pretty much impossible to take pictures for this step.
Step 7: How to Make an Improvised Vise With a C-Clamp
I made this way before my grandpa gave me my vise. This was taken apart the day I restored my metal vise, meaning that these pictures was taken a long time ago, so sorry for the quality...
