How to Make a Homemade Wood Vise
- Step 1. Use a tape measure to measure in three inches from each end of the 2-by-8-by-12-inch hardwood board.
- Step 2. Place the 2-by-4-by-12-inch hardwood board in front of you. Measure and mark three inches from each end of the...
- Step 3. Use a screw gun and three-inch deck screws to fasten the base of the vise to the back-bottom side of...
Full Answer
How to build a bowling ball vise?
“Fill the opened cavity almost to the top with lead shot to add weight, then seal the shot to the top of the hole with automotive Bondo® filler.” “Make a round cover for the flat top of the ball using metal, wood or Formica®. Mount your vise on top of this. Mine is a machinist’s vise using its mounting system.” “Make a base and you’re almost done.
How to make a wood vise?
Make a Bench Vise for Woodworking
- What You Need. About 16 linear feet of one by six hardwood (actual measurements ¾” x 5½”). ...
- Front Jaw. Cut two 32” long pieces from the one by six board. ...
- Rear Jaw. The rear jaw is L-shaped. ...
- Drill Holes for the Hex Bolts. Drill two ½” holes through the front jaw 3” from the short edge and 2 ¼” from the top edge. ...
- Make Handles. ...
- Use Your Bench Vise. ...
How to mount a woodworking vice?
Mounting a Wood Vise
- Select which Side. Choose which side of your workbench you will mount your work vise. ...
- Position the Wood Vice. Place the Wood Vice where you want it before bolting. ...
- Measuring. Mark out the holes where it requires bolting. ...
- Drilling. Then, drill the holes to allow the bolts to pass through your workbench. ...
- Bolting. ...
- Installing. ...
How to attach a vise to a drill press?
How to attach a Vise to a Drill Press
- Place the drill vice press atop the table of the drill press.
- Align the holes on the drill press vise with holes on the drill press table.
- Slide a 3/8 washer over 3/8 inch bolt and gently inch this through the hole aligned on the drill press table.
- Rotate the drill press vise to align another hole with the drill press table. ...
What can I use instead of a vise?
1:092:42Two Ways to Hold Wood Without a Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake another piece of wood and drill a hole the diameter of your pipe clamp screw this on to yourMoreTake another piece of wood and drill a hole the diameter of your pipe clamp screw this on to your table. Take the back of the pipe clam. And look we've got a vise here.
How can I make a vise?
0:117:17How to make a Workbench Vise ( DIY MOXON VISE ) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe radius jig definitely made this a little easier and more accurate. But you can totally use a jigMoreThe radius jig definitely made this a little easier and more accurate. But you can totally use a jig saw to round this over. On one side of the jaw. I need to round out a dado slab.
How do you make a metal vise?
2:5210:06Make A Metal Drill Press Vise Without Welding - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe process here is the same as in all connection points in its build drilling a pair of holes inMoreThe process here is the same as in all connection points in its build drilling a pair of holes in each part to secure it with m12 allen bolts. This angle iron is way too thin for my planet.
How do you make a vice clamp?
1:107:296 homemade clamps and workbench vises - YouTubeYouTubeStart of suggested clipEnd of suggested clipThese are just a couple of strips with two bolts. I put the work pieces between the strips. AndMoreThese are just a couple of strips with two bolts. I put the work pieces between the strips. And there are a lot of holes all along both strips.
How do I make a portable bench vise?
0:271:27How to make your bench vice portable - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow that you've drilled the holes you're going to turn the board over and Mark out the top of theMoreNow that you've drilled the holes you're going to turn the board over and Mark out the top of the bolts. So now you want to chisel out like this so the ball is sits under the surface.
What metal is used to make vise clamps?
It is sometimes made of cast steel or malleable cast iron, but most are made of cast iron.
How is a bench vise made?
Bench vises are commonly made in two distinct processes: casting and forging. Casting is the most common and cost effective manufacturing process. It involves pouring hot liquid metal into molds. Once poured into the mold the liquid steel is allowed to cool.
How do you make a drill press vise?
3:539:44Homemade Drill Press Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipI cut the pins which are just wooden dowels down to their final size and tested the fit of theMoreI cut the pins which are just wooden dowels down to their final size and tested the fit of the backing on the base. After that I started laying out the rest of the components. I decided on pre
How do you weld a vice?
0:211:20Stick Welding A Cast iron Vise Repaired with 77 Electrode from ...YouTubeStart of suggested clipEnd of suggested clipBit i slightly warmed up the weld area with a map oxy. Torch. Final cleaning with a fine wire wheelMoreBit i slightly warmed up the weld area with a map oxy. Torch. Final cleaning with a fine wire wheel then slowly laid down the root pass a half inch at a time peening with a punch between passes.
How do you make a pipe clamp vise?
0:159:22Pipe Clamp Workbench Vise - 210 - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut instead of making something very similar to it to sit on top I want to make a twin pipe clampMoreBut instead of making something very similar to it to sit on top I want to make a twin pipe clamp style bench vise to go on the end of this particular work table just like the previous vise.
How do you make a woodworking vice?
0:426:39DIY Woodworking Bench Vise - Quick and Easy Shop Project - YouTubeYouTubeStart of suggested clipEnd of suggested clipGrooves. This will make the dovetail cuts cleaner. And will reduce the wear and tear on my dovetail.MoreGrooves. This will make the dovetail cuts cleaner. And will reduce the wear and tear on my dovetail. Bit i went with two equally spaced horizontal cuts. And three equally spaced vertical.
How do you make a wooden screw vise?
1:0713:03Making a Traditional Leg Vise With a Wooden Screw - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf it's out already. But today we're gonna be talking about this traditional style this is a woodenMoreIf it's out already. But today we're gonna be talking about this traditional style this is a wooden screw a two and a half inch wooden screw from Lake Erie.
How do you make a woodworking vice?
0:426:39DIY Woodworking Bench Vise - Quick and Easy Shop Project - YouTubeYouTubeStart of suggested clipEnd of suggested clipGrooves. This will make the dovetail cuts cleaner. And will reduce the wear and tear on my dovetail.MoreGrooves. This will make the dovetail cuts cleaner. And will reduce the wear and tear on my dovetail. Bit i went with two equally spaced horizontal cuts. And three equally spaced vertical.
How do you make a wooden screw vise?
1:0713:03Making a Traditional Leg Vise With a Wooden Screw - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf it's out already. But today we're gonna be talking about this traditional style this is a woodenMoreIf it's out already. But today we're gonna be talking about this traditional style this is a wooden screw a two and a half inch wooden screw from Lake Erie.
How do you make a drill press vise?
3:539:44Homemade Drill Press Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipI cut the pins which are just wooden dowels down to their final size and tested the fit of theMoreI cut the pins which are just wooden dowels down to their final size and tested the fit of the backing on the base. After that I started laying out the rest of the components. I decided on pre
How do you make a Moxon vise?
0:0815:06$40 Moxon Vise - Easy to build in an afternoon! - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis kit comes with everything that you need to build a quality Moxon vise it also comes with a setMoreThis kit comes with everything that you need to build a quality Moxon vise it also comes with a set of instructions.
Step 1
Use a tape measure to measure in three inches from each end of the 2-by-8-by-12-inch hardwood board. This board is the back jaw of the vise. Make a pencil mark at this measurement in the center of the board on each end. Do the same with the 1-by-8-by-12-inch hardwood board. This board is the front jaw of the vise.
Step 2
Place the 2-by-4-by-12-inch hardwood board in front of you. Measure and mark three inches from each end of the board. Use a drill and ¼-inch drill bit to drill through the board at the pencil marks. This board will form the base of the vise.
Step 3
Use a screw gun and three-inch deck screws to fasten the base of the vise to the back-bottom side of the back jaw of the vise. Screw through the front of the back jaw into the base of the vise. Space the screws evenly every 6 inches.
Step 4
Place the base of the vise onto the edge of the vise mounting surface. The back jaw of the vise should hang off the edge of the surface. The base should be fully on the mounting surface. Use a ¼-inch wrench to fasten the base of the vise to the mounting surface using the ¼-inch lag bolts.
Step 5
Slide one 3/8-inch fender washer onto each of the 3/8-by-8-inch carriage bolts. Slide the carriage bolts through the back side of the holes in the back jaw plate of the vise. Slide the front jaw plate onto the carriage bolts from the front side. Slide the remaining to fender washers onto each of the carriage bolts.
Step 1: Welding a Nut to a Base
I want to use a M16 threaded rod for the linear movement. Therefore I need a nut or something threaded to interact with the rod. I decided to weld a M16 nut to a flat plate connector. The flat plate connecter has already some holes to fix this part to the workbench. Unfortunately I don't have a welder so I asked my dad to do this job for me.
Step 2: Welding a T-Piece, a Washer and the Rod
I want to use a T-piece pipe to hold the threaded rod and a wooden rod later. The tee has two 3/4" ends and one 1/2" end.
Step 3: First Test Run
Both parts are finished. Let's try if everything fits together. Looks very good. The difficult part is done. Now comes some woodworking.
Step 4: The Moveable Jaw
So what we need next is a moveable jaw for the vise. My dimensions are 40cm by 15cm, but you can adjust them to your needs. I use scrap wood I have laying around. I would use some kind of hard wood for the jaws, but unfortunately I don't have enough, but I use a little trick.
Step 5: Mounting the Rod and the Support Pipes to the Jaw
I use two 5/8" copper pipes to support the rod and to keep the jaw from rotating. They have a length of 50cm. You can adjust the length to your needs.
Step 6: Drilling the Holes to the Workbench Jaw
This time I need three holes which go right through the workbench. I use my rack to get everything in a right angle. I finish the surface with a sander.
Step 7: Building the Flange
Remember the washer, which we welded to the T-piece? Now you'll see its purpose. I need some kind of flange, which will connect the jaw to the rod, but still loose enough to allow rotation. This allows the jaw to move with the rod while opening the vise.
