Pipe Clamp Bench Vise
- Step 1: Measure for Mounting. I recently built a workbench for my miter saw and left space for this vise. I measured the...
- Step 2: Cut to Length. I trimmed the ends of both jaws, and then trimmed one board to 26".
- Step 3: Align for Pipe Holes and Drill. I lined up where I wanted to drill and used a square to draw lines across both...
How to make a pipe clamp bench vise?
Pipe Clamp Bench Vise 1 Measure for Mounting. I recently built a workbench for my miter saw and left space for this vise. ... 2 Cut to Length. I trimmed the ends of both jaws, and then trimmed one board to 26". 3 Align for Pipe Holes and Drill. ... 4 Mount Pipe Clamp to Jaws. ... 5 Mount the Fixed Jaw to the Bench. ... 6 All Done! ...
How do you use a pipe vise?
Insert the pipe into the jaw and slide the assembly into position on the bench. clamp head mounting screws. line with it on your bench’s top. to your workpiece’s size. I fastened my adjustment pin to the jaw using screw eyes and a light chain, so it doesn’t get lost. I used a 16" pipe for this vise. Like the face vise, reach under
What is the best pipe clamp to use?
any brand of pipe clamp will work. fit a larger, stationary bench, too. Face vise. any bench. It’s usually the first—and buy. Typically, it holds boards so their edges can be worked. Click any image to view a larger version.
How do I install the clamp heads on the pipe?
Drill screw holes in the clamp heads. Insert the pipe into the jaw and slide the assembly into position on the bench. clamp head mounting screws.
How do you make a vise clamp?
1:107:296 homemade clamps and workbench vises - YouTubeYouTubeStart of suggested clipEnd of suggested clipThese are just a couple of strips with two bolts. I put the work pieces between the strips. AndMoreThese are just a couple of strips with two bolts. I put the work pieces between the strips. And there are a lot of holes all along both strips.
How do you make a workbench clamp?
0:117:17How to make a Workbench Vise ( DIY MOXON VISE ) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe radius jig definitely made this a little easier and more accurate. But you can totally use a jigMoreThe radius jig definitely made this a little easier and more accurate. But you can totally use a jig saw to round this over. On one side of the jaw.
How do you make a woodworking pipe clamp?
0:293:55How to Assemble Pipe Clamps - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo home depot or lowes. And one tip for that would be this what I've got here is two three footMoreSo home depot or lowes. And one tip for that would be this what I've got here is two three foot lengths and a four foot length.
How thick should Wood be for vise?
I would recommend at least one inch of hardwood onm the outside face of the chop. The inside face need not be as thick since it will not be compressed during tightening, so about 1/2" should do it.
What can I use instead of a vise?
Cut out this bird's mouth shape using whatever you have: a back saw, jig saw, coping saw, band saw. Set up the long piece of wood as a stop against the end your worksurface. If you're right handed, that's the left side; if you're a leftie, then the right side. Clamp or screw it in place.
How do you make a carpenters bench vice?
0:426:39DIY Woodworking Bench Vise - Quick and Easy Shop Project - YouTubeYouTubeStart of suggested clipEnd of suggested clipOver at the table saw i cut a piece of 1 inch thick ash to 5 inches wide for the face of the vise.MoreOver at the table saw i cut a piece of 1 inch thick ash to 5 inches wide for the face of the vise.
What kind of pipe do I use for pipe clamps?
There are two acceptable types of pipe you can use with pipe clamps: galvanized pipe and black steel pipe—the same type traditionally used for gas lines. Either will work fine, but the black pipe is less expensive, which makes it the preference for woodworkers on a strict budget.
How long should I make pipe clamps?
0:472:56How to assemble pipe clamps - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust slight pressure three hours you're done.MoreJust slight pressure three hours you're done.
Do Pipe clamps need threaded pipe?
Most stores will even cut threads onto the ends of the pipes for free should your pipe clamp require threaded ends. The longer lengths are usually 10-foot lengths of pipe, which you can then cut into varying lengths.
What kind of wood do you use in a wood vise?
Generally, maple is used for wood vise jaws as it is durable enough to withstand the clamping force of a vise. However, softer woods such as pine can be used if your projects will be made from mostly soft hardwoods like cherry to prevent marring.
How do you protect wood in a vise?
0:151:08How to Prevent a Workshop Vice from Damaging Wood - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust put it in place crank. It down I matter how much pressure you put on this. You're going to haveMoreJust put it in place crank. It down I matter how much pressure you put on this. You're going to have those pads in place.
How wide should a leg vise be?
For hardwoods you want at least 1.5" thick and for soft woods I would not go less than 2.5". Make it as long as your bench top to a few inches off the ground. In my case I am using a slab of Cherry 2.5" thick, 14" wide, and 31" long.
How do you make a dog hole clamp?
1:354:13DOG HOLE CLAMPS MADE FROM HARBOR FREIGHT BAR CLAMPSYouTubeStart of suggested clipEnd of suggested clipFor the clamp to fit into and the easiest way I determined to do that was on the table saw with aMoreFor the clamp to fit into and the easiest way I determined to do that was on the table saw with a jig that I built just clamp the dowel in the jig.
How do you make a clamping table?
0:5911:26Save Huge Money Building a Clamping Table | WoodworkingYouTubeStart of suggested clipEnd of suggested clipI just cut out some parts on their CNC. And glued and tack these together with an 18 gauge bradMoreI just cut out some parts on their CNC. And glued and tack these together with an 18 gauge brad nailer. So I can keep moving. Forward.
How do you clamp a wooden work bench?
0:038:45Quick-Clamp Vice for the Workbench - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey're simply better if you want to see how I did it stick. Around. When you're done grinding offMoreThey're simply better if you want to see how I did it stick. Around. When you're done grinding off the stops you should be able to remove. And slide the stopped end of your clamp up and down freely.
How deep should bench dog holes be?
Step 1: Materials. There's no standard size for bench dogs, but I've found that 3/4" or 1" to be the most common size for round dogs. I had drilled 3/4" openings in my workbench, so that's the size of dowel I'll need.
Face Vise
This is the simplest and most-used vise of the three. You can use whatever length pipe you like, but I find that a pipe about 14" long is sufficient for most tasks (Fig. A).
Fig. B: Pipe and Guide Rod Locations
Squeeze the pipe clamp’s clutch plates to adjust the jaw in or out to suit the size of your workpiece.
Tail Vise
Like the face vise, first glue up the jaw (A) and faceplate (B) assembly. You could probably get by without the faceplate, but a stout wood like oak stands up to hard use much better than pine. Square up the assembly using a jointer and planer, if available. If not, a tablesaw or circular saw will do.
Fig. D: Guide Board Hole Pattern
Insert the adjustment pin in the hole that gives you the jaw opening best suited to your workpiece. Adjust the pipe clamp by squeezing the clutch plates to release their grip.
Moxon Vise
Named after 17th-century woodworker and author Joseph Moxon, this vise specializes in securely holding wide boards. Two clamps provide even clamping pressure across the whole board with no racking. Th e main feature my version has that the original didn’t is a quick-release mechanism (Fig. G and photo below).
Step 2: Prepping the Workbench
It feels so wrong to do it, but I start by cutting off the edge of my workbench top. This overhang off the top is a little shy of 3" and was designed for use as an easy clamping surface to hold things on the bench, but I also figured it would make the perfect place to install a full width vise in the future.
Step 3: Disassembling the Pallets
Sourcing pallet wood has become more and more difficult. These days the only way to get usable material is to beat it out of them. They might try to just cower away and trick you, but jokes on them, you and I both know it's a 2 step process.
Step 4: Picking the Slats and Shaping Them
With my new pallet slats, they are all run through the thickness planer until smooth and then I match up pairs that are the same thickness and combine to over 6" in width since they will be glued side by side to make up the block that will be the vise.
Step 5: The Glue-up
So now it's just a matter of making a big pallet wood and wood glue sandwich. Actually, there must be some weird chemicals in this wood because the wood just kind of took over things from here...
Step 6: Sizing the Glue-up
With the glue dry, I can now mill down my new chunk of pallet wood lumber. I start by cutting the ends even on the miter saw.
Step 7: Reinforcing the Bench and Installing the Pipes
Now I have to prepare the bench to receive the vise. The skirt board is only a little over 1" thick so I need to beef it up a bit. I add in 2 more of these same pieces by screwing it to the legs with pocket hole screws and also by gluing them each to the skirt board and clamping the whole thing together while it dries.
Step 8: Routing the Slots and Recess
Now the clamps are screwed tight and I trace out the face of the clamps so I can recess them into the outer face of the vise.