- Step Two: Cut two matching layers of plywood to the same size. Step Three: Cover one side of each piece with glue, then...
- Step Six: Now, lay out the mounting holes on the bottom of your top plate. Trace the outlines, then find the center.
Full Answer
How do you mount a post Vice?
Find a short piece of pipe that will go around the end of the post (at the bottom), weld it to a piece of scrap plate, drill a couple holes through the plate and lag bolt it in position below wherever you are going to mount it (to a bench). Don't overthink the mission. "Mounting a Post Vice"!! K.I.S.S. More sharing options...
How do you anchor a vise to the ground?
The bottom of the post should be firmly anchored so that vertical forces from hammering on something held in the jaws will be carried down through the post to the ground/floor. The mounting plate between the jaws and the pivot point is holding the vise against lateral forces and twisting forces from the jaws.
How high do you mount your vises?
My vises are mounted at several different heights I hava a seven inch vise mounted low for striking and ground Vs in the jaws for firmly holding hardy shanks on some of my tooling. All of the vises are mounted on 4 or 6 inch heavy wall square tubing somewhere between 4 to 5 feet deep in the foor in concrete. When I hit them they DONT move.
Can you use a post vise in the ground?
Don't use concrete or cement to secure the post vise in the ground. You will regret it when you have to dig the post out. As it ages, weather conditions, humidity, and the torque which transfers from the vise to the post, it will eventually create weak points and the post will start to split and you'll have to replace it-which means.
How do you mount a pole vice?
0:437:06Blacksmith Post-Vice Mount - YouTubeYouTubeStart of suggested clipEnd of suggested clipEither in a concrete or in this case a piece of metal tubing. This was a very common device youMoreEither in a concrete or in this case a piece of metal tubing. This was a very common device you would see in a blacksmith shop these were used before your typical bench vise became popular.
How do you do a post vise stand?
0:086:54Building the ULTIMATE Post Vise Stand| Iron Wolf Industrial - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe bill of $15 at scrap price and pick yourself up one of these. In addition we're going to need aMoreThe bill of $15 at scrap price and pick yourself up one of these. In addition we're going to need a welder and some sort of oxy-acetylene. Or plasma capability for any cutting we might need to do.
How do you install a leg vise?
3:357:00Installing a Leg Vise on a Workbench - 253 - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe nut on from the backside. And then secure the nut with a couple wood screws. The leg vise thatMoreThe nut on from the backside. And then secure the nut with a couple wood screws. The leg vise that we are installing is modeled after the leg vise that I use in my shop.
How do you use Post leg vise?
0:083:36Post Leg Vice Walk Around // My Blacksmith Vice and ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I'm going to show you everything that's about my vise how I set it up and how its handy thanksMoreAnd I'm going to show you everything that's about my vise how I set it up and how its handy thanks for watching. Okay everyone here is my leg vise that I use on a daily basis.
How does a post vise work?
A blacksmith's post vise or "leg vise" is designed to be hammered on, unlike most bench-mounted machinist vises. The long leg transmits the energy from hammer blows all the way from the massive fixed jaw to the floor. Hot iron is secured in the vise and then shaped as needed by hammer blows.
How do you make a vise stand?
1:108:06How to Make a Vise Stand From Scrap Metal - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm just getting some rough locations. So when i go to weld it'll be easier to. Align i think i cutMoreI'm just getting some rough locations. So when i go to weld it'll be easier to. Align i think i cut this post to make the top of vice finish out at 36 inches i did this to match my other extra hand.
How do you forge a leg vise?
6:0519:39Forging a Leg Vise part2! 4000 Sub Challenge?? - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then draw its piece into our toe. We're going to do that on both of these these sections hereMoreAnd then draw its piece into our toe. We're going to do that on both of these these sections here Forge that down and then using the same chisel I'm hoping to be able to slit.
What is a tail vise?
A tail vise's main purpose is to hold a board flat on the bench for planing, routing, sanding and so on. The tail vise pushes a board tightly against a bench dog so the board can't swivel or move. The bench dog fits in a series of holes cut in the top to accommodate different sizes of boards.
What is a face vise?
Face vises are designed specifically for holding wooden workpieces while such operations as drilling and sawing are performed. The traditional material is wood. A wood face vise consists of a movable front jaw that is mounted to a broad, square beam that slides in and out of a matching channel.
Why do blacksmiths use leg vise?
What makes a leg vice special? One is that they are forgings, not cast iron or ductile iron. The second is the leg which provides support to the floor or from a sunken post. The leaf spring is a critical part of the vice, as it enables you to work quickly when securing your work.
What is the benefit of a leg vise?
The biggest advantage to the leg vise is the deep throat of the vise. The throat is the distance from the top of the bench to the screw. The large throat allows wide boards to be secured so the edges may be worked. Very long boards can be secured if a board jack is used to support the un-clamped end.
How does a blacksmith leg vise work?
0:3710:04Vises for the blacksmith shop - tool of the day - YouTubeYouTubeStart of suggested clipEnd of suggested clipLike it does in a modern machinists vise the jaws are actually loose. And it's just a spring thatMoreLike it does in a modern machinists vise the jaws are actually loose. And it's just a spring that the heat makes it feel tight. But the jaw can move and wiggle a little bit. Because all of the weight.
How do you make a wooden vise stand?
0:2911:20How to Make a 200lb Mobile Vise Stand | DIY Woodworking ProjectYouTubeStart of suggested clipEnd of suggested clipAll right so we're gonna start this off by cutting down some Baltic birch plywood. This is three-MoreAll right so we're gonna start this off by cutting down some Baltic birch plywood. This is three-quarters of an inch in thickness.
How do you make an anvil stand?
0:1510:17Making a Blacksmith Anvil Stand - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe steeper the legs the more force they'll be able to take but if they're too steep then it willMoreThe steeper the legs the more force they'll be able to take but if they're too steep then it will lose stability. You could spray the legs out that will give it more stability.
What is leg vice?
The leg vise can be visualized as a giant wooden hand screw clamp placed vertically . This form of vise probably evolved from the blacksmith's iron post vise. Leg vises typically use the left front leg of the bench as the rear jaw of the vise.
How does an anvil work?
An anvil is a metalworking tool consisting of a large block of metal (usually forged or cast steel), with a flattened top surface, upon which another object is struck (or "worked").
What is the purpose of the mounting plate between the jaws and pivot point?
The mounting plate between the jaws and the pivot point is holding the vise against lateral forces and twisting forces from the jaws. If you think about those forces you will be fetter able to design rigid mounting points.
Can you use a telephone pole cull vise?
You'll want to make sure the vise is mounted securely to a post that has a diameter large enoough to hold the vise, and the weight of the work you're working on. My vise could hold material weighing several hundred pounds (wagon wheel). You can buy treated telephone pole culls. They've been treated specifically to be placed in the ground, so they last a long time.
Can you use cement to attach a post vise?
Don't use concrete or cement to secure the post vise in the ground. You will regret it when you have to dig the post out. As it ages, weather conditions, humidity, and the torque which transfers from the vise to the post, it will eventually create weak points and the post will start to split and you'll have to replace it- which means...dig out the concrete or get the backhoe and chain the post and wrench it out.
How to use a 55 gallon drum for a vise?
One way is to use a 55 gallon drum, fabricate a mount for the vise and then fill the drum with water after it is placed where you want it . Also makes it relatively portable for away demonstrations. Another mounting method involves getting a truck rim for a base, welding a vertical pipe or pipes and then topping with a steel plate to mount your vise to. A third involves builing a tripod stand like the old pipe vises were mounted on.#N#Important to decide what you are going to be doing with the vise. I mean are you going to be hammering metal held in the vise, trying to twist a five foot bar, grinding, welding or what? This affects how secure the want the vise.
Can you use a tripod with angle iron?
A tripod out of heavy angle iron works well in a portable application . You make a truncated cone (top is flat) and put a plate there to attach the vise. It would be even better if you could also drill some holes in the slab and epoxy in some threaded sockets to match feet on the tripod. That way, it can be bolted down for really heavy twisting or bending but still moved when need be.
How long does it take to attach a bench dog to a bench?
This might be useful in the future if I'm cutting something quite long and need the side-to-side clearance and support in the middle. This took about 6 seconds.
Can you reinforce dado joints?
Allow the glue to cure. You could reinforce this dado joint with screws or dowels if you want, but with this much contact and the dimensional strength of the plywood, I think it'll stand up to any force I can apply with my hands. Also, at this point, I wiped on a coat of Danish Oil.
Step 2: Precautions......
We are going to be using a drill. Drill bits can and will drill through things, including body parts. Please do not do that. But if you happen to try it out, remember that I AM NOT RESPONSIBLE FOR YOUR TESTING, or TESTING RESULTS... Also, please wear safety glasses!
Step 3: Where Is Your Vise Going?
So, once you know where you want to mount your vise, use a pencil or marker to mark where.
Step 4: Mount It Up!
Put that there Vise into place and then hand tighten the bolts. You then use the half inch bit to tighten them down!
