Visa-Faq.com

how to mount a workbench vise

by Garnet Ratke Published 3 years ago Updated 2 years ago
image

  • Measure the worktable.
  • Measure out and cut out the jaws to length.
  • Align and drill the pipe holes.
  • Mount the pipe clamps to the jaws.
  • Mount jaws to the bench using nuts and hex head bolts for mounting a bench vise.

Part of a video titled Mounting a Workbench Vise - YouTube
1:09
10:36
The end vise on the bench top by first removing the nuts that hold the end assembly to the guideMoreThe end vise on the bench top by first removing the nuts that hold the end assembly to the guide rods. Go ahead and slip that out. And set it aside.

Where should you mount a vise on a bench?

Right-handers should mount a face vise at the far left of the bench’s front edge and an end vise on the end of the bench at the foremost right-hand corner. Southpaws will want to do the opposite. When retrofitting an existing bench, make sure the vise mechanism won’t interfere with the bench legs. Shift the top if necessary to accommodate the vise.

How to install a bench vise pipe clamp?

Here’s how to install a bench vise pipe clamp: Measure the worktable. Measure out and cut out the jaws to length. Align and drill the pipe holes. Mount the pipe clamps to the jaws. Mount jaws to the bench using nuts and hex head bolts for mounting a bench vise.

Can you use a metalworking vise for woodworking?

If you use a metalworking vise for woodworking that has metal jaws when you tighten them they will dent and damage your woodworking project. You can always use a scrap piece of wood on either side to caution the clamping mechanism and to help avoid any damage if you have the wrong type of vise. 3. Pipe clamp bench vises

How did you build your first Workbench?

My first “workbench” was a simple table-style surface. 2×4 legs, 1/2″ plywood top, held together with black drywall screws. I built it in my first apartment when I was twenty-two, with my first (and only) power tools: a circular saw and a drill. In the back left corner, I mounted a shiny, new, bright blue Irwin swiveling bench vise.

image

Where is the best place to put a vise on a workbench?

That's why face vises usually are placed on the left end of the bench. When sawing workpieces (below), a left-side vise also lets you hold onto the offcut, with the keeper piece safely secured in the jaws, resulting in a cleaner cut. But that said, you can mount a vise wherever it suits you best.

How do you hang a vise without a bench?

2:096:17Mounting a vise without taking up bench space. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you just go to the spot that it's at. And the holes are just a little bit loose so that they don'MoreSo you just go to the spot that it's at. And the holes are just a little bit loose so that they don't bind up.

How thick should wood be to mount a vise?

Step One: Begin by making a plate to mount the vise. I'm using a double layer of 3/4″ plywood here, since it's dimensionally stable and strong in both directions, and can be easily cut to larger sizes without milling and gluing up panels.

How do I temporarily mount a vise?

0:001:03Portable Vise Mount - YouTubeYouTubeStart of suggested clipEnd of suggested clipI have a little lip around the board keeps it flush to the match. And you can mount this on anyMoreI have a little lip around the board keeps it flush to the match. And you can mount this on any bench you can mount in any height. And it's a good way to keep the vise.

How do you attach a vice?

0:281:57How To Properly Mount A Vice To Any Surface.. - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's going to go right on top I already pre-drilled the holes. Bolts washer it's going to go rightMoreIt's going to go right on top I already pre-drilled the holes. Bolts washer it's going to go right through. Now. I'm going to drill holes on here to match here. And then what I'm going to do is once I

What kind of wood do you use in a wood vise?

Generally, maple is used for wood vise jaws as it is durable enough to withstand the clamping force of a vise. However, softer woods such as pine can be used if your projects will be made from mostly soft hardwoods like cherry to prevent marring.

What bolts to mount vise?

Re: Mounting a Bench Vise Mine used 7/16 bolts to mount. Make sure to hang the jaws over the edge of the table, just as ware did.

What clamping position should be considered when mounting a vise on a workbench?

What clamping position should be considered when mounting a vise on a workbench? The vise should be positioned so that a long piece can be held vertically in the jaws without interference from the workbench.

How do you make a removable bench vise?

0:052:13Woodworkers need a removable machinist vise/anvil mounting system!YouTubeStart of suggested clipEnd of suggested clipAttach. It with a glue and screws. So it's nice and secure. This will clamp inside my woodworkingMoreAttach. It with a glue and screws. So it's nice and secure. This will clamp inside my woodworking vice no muss no fuss. You've probably seen people do this before.

How do you put a vise on a tool box?

1:113:26How to mount a bench vise to a Husky tool box - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I'm gonna go all the way through the wood to the top toolbox. And then I'll just mount it onMoreAnd I'm gonna go all the way through the wood to the top toolbox. And then I'll just mount it on those three. Points. Can I just wallow death the holes a tiny bit just make them a little bit.

How do you secure a vise table?

2:2511:30How To Install A Vise Like A PRO - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure you have enough room to get that nut on there without it conflicting. Also reach upMoreMake sure you have enough room to get that nut on there without it conflicting. Also reach up underneath there on the bottom side as well if you can only get three bolts in it that's okay.

How do you install a front vise?

2:064:38How to install a Woodworking Vise// Woodworking// Quick Release ViseYouTubeStart of suggested clipEnd of suggested clipThen install the screws that will mount the front of the vise to the front jaw take quick-releaseMoreThen install the screws that will mount the front of the vise to the front jaw take quick-release vise you just barely want to put the screws in the guide rods in place so that you can situate.

Can you reinforce dado joints?

Allow the glue to cure. You could reinforce this dado joint with screws or dowels if you want, but with this much contact and the dimensional strength of the plywood, I think it'll stand up to any force I can apply with my hands. Also, at this point, I wiped on a coat of Danish Oil.

How long does it take to attach a bench dog to a bench?

This might be useful in the future if I'm cutting something quite long and need the side-to-side clearance and support in the middle. This took about 6 seconds.

What to do if you don't have a table saw?

If you don't have a table saw, you can do this with a circular saw or even a handsaw. Just make sure to mark a baseline, and keep everything secure.

Do I need to clean my Douglas fir blade?

Yes, I know I need to clean my blade. I've been cutting a lot of relatively fresh Douglas fir for a project, and the pitch has left a lot of build-up. I'll be following this tutorial soon!

How big of a vise should I use for face planing?

Because a face vise is used for general work as well as for planing edges, I recommend investing in a larger vise (at least 10"). Since it’s primarily used in tandem with bench dogs to secure boards for face-planing, a smaller end vise should suffice.

How to attach a vise to a spacer block?

Use a straightedge to ensure the face of the jaw is flush with the edge of the ben ch. If it’s proud, level it with a hand plane.

How to measure spacer block thickness?

To determine the thickness of your spacer blocks, place the rear jaw upside down on the inverted benchtop and measure how much the top of the jaw projects beyond the underside. Add to that 1⁄4" for a 7" vise, or 1⁄2" for a 10" vise. (The former is necessary for better dog height on the smaller vise.)

How to make a cheek on a bench?

Make the front cheek, and attach it with washers and roundhead woodscrews, reassemble the vise, and turn the benchtop over. Hand-plane the cheeks flush with the benchtop (Photo H). My bench had radiused edges, so I chiseled away the sharp point at the corner of the cheek. Finally, apply a couple of coats of wipe-on finish to all raw wood surfaces.

How big is a face vise?

Because a face vise is used for general work as well as for planing edges, I recommend investing in a larger vise (at least 10"). Since it’s primarily used in tandem with bench dogs to secure boards for face-planing, a smaller end vise should suffice. I prefer a small (7") model, because its dog is only 31⁄2" from the front edge of the bench, which is convenient for clamping workpieces for face-planing and other operations.

How to cut a notch in a bench?

Make the crosscut into the benchtop edge with a backsaw. Then clamp a straightedge to the bench to guide a circular saw to cut the length of the notch. Rip the notch until you intersect the previous crosscut (Photo C), and then finish up with a handsaw.

What is a workbench without vises?

Let’s face it; a workbench without vises is basically just an assembly table. Vises provide the muscle for securing workpieces for planing, sawing, routing, and other tooling operations. Of the myriad commercial models, the venerable Record vise is one that has stood the test of time, because it’s simple to install, easy to operate, and designed to survive generations of use. Although it’s no longer in production, several clones are available, including the Eclipse vise, which I show in this article. Similar vises may differ in features, but attachment is similar.

What makes the ideal workshop table with a bench vise?

Ideally, you have a strong steel bench for mounting a bench vise, with a plywood replaceable top to cushion the rigid steel and prevent damage or rust marks on your projects.

How to mount a pipe clamp bench vise?

If you want to DIY a custom-fit pipe clamp bench vise. Though you can purchase ready-made ones if you prefer. Here’s how to install a bench vise pipe clamp:

What other tools can you mount next to a bench vise?

A bench grinder is a great tool to have next to your bench vise. With a capable motor and two grinding wheels, having it near your bench vise allows you to easily and constantly keep your tools sharp. If you are doing metalwork, a bench grinder allows you to smooth out and polish workpieces.

Would bench vise replace clamps?

Yes and no. Though wood and metal clamps are viable, especially for simpler tasks, a bench vise just offers more flexibility and strength for holding smaller objects securely.

Why do vises have lined jaws?

As the most common of vise types, these typically have either wood or lined jaws to help prevent damaging the workpiece you clamp from the clamping jaws.

What is a vise tool?

Being made out of two parallel jaws, an adjustment screw, and a base; a vise is a tool that’s simple to both operate and maintain.

What is metal vise?

Metalworking vises are mainly used to clamp down metal but are also more viable than woodworking vises when needing to secure large and heavy materials.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9