What is the purpose of a leg vice?
It uses two arms that are pinned to the jaw and leg at the top and connected to each other with a pin at the mid-point of the arms. The bottom of each arm rides against metal plates inset into the jaw and leg. This mechanism allows the jaws to be held parallel regardless of how wide the vise is opened.
Why do blacksmiths use leg vise?
What makes a leg vice special? One is that they are forgings, not cast iron or ductile iron. The second is the leg which provides support to the floor or from a sunken post. The leaf spring is a critical part of the vice, as it enables you to work quickly when securing your work.
How do you use blacksmith leg vice?
0:1010:04Vises for the blacksmith shop - tool of the day - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut the jaw can move and wiggle a little bit. Because all of the weight. From working on the theMoreBut the jaw can move and wiggle a little bit. Because all of the weight. From working on the the jaws up here is transferred down through that portion of the vise. To.
What is the purpose of a vise?
vise, also spelled Vice, device consisting of two parallel jaws for holding a workpiece; one of the jaws is fixed and the other movable by a screw, a lever, or a cam. When used for holding a workpiece during hand operations, such as filing, hammering, or sawing, the vise may be permanently bolted to a bench.
How do you mount a leg vise?
0:577:00Installing a Leg Vise on a Workbench - 253 - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe don't necessarily need to shim the entire base to match the overhang. Instead we're going to addMoreWe don't necessarily need to shim the entire base to match the overhang. Instead we're going to add a front jaw to the vise. And to do so we need to remove just a little bit of material.
What is a leg vice made of?
Leg Vices were traditionally made from Wrought Iron and are still Forged in steel.
How do you identify a post vise?
2:384:57Identifying blacksmith leg vise material, wrought iron, steel, etc - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe bottom left is the cast iron swage block and the bottom right is the high carbon steel.MoreThe bottom left is the cast iron swage block and the bottom right is the high carbon steel.
How do you do a post vise stand?
0:086:54Building the ULTIMATE Post Vise Stand| Iron Wolf Industrial - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe bill of $15 at scrap price and pick yourself up one of these. In addition we're going to need aMoreThe bill of $15 at scrap price and pick yourself up one of these. In addition we're going to need a welder and some sort of oxy-acetylene. Or plasma capability for any cutting we might need to do.
What are the different types of vices?
Different Types Of VicesDril lMachine Vice.G Claimp.Bench Vice.Baby Vice.Hacksaw Frames.Pipe Vices.Bearing Pullers.Pipe Vice.More items...
What are different types of vises?
Types of VicesBench Vice.Pipe Vice.Tool Makers Vice.Hand Vice.Leg Vice.Drill vice.Pin Vice.
What type of vise do I need?
For general household DIY, a 4- to 5-inch vise is large enough to handle most tasks. (This measurement is the length of the jaws from end to end and is maximum amount of contact your vise has with the workpiece.)
How do you identify a post vise?
2:384:57Identifying blacksmith leg vise material, wrought iron, steel, etc - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe bottom left is the cast iron swage block and the bottom right is the high carbon steel.MoreThe bottom left is the cast iron swage block and the bottom right is the high carbon steel.
How do you do a post vise stand?
0:086:54Building the ULTIMATE Post Vise Stand| Iron Wolf Industrial - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe bill of $15 at scrap price and pick yourself up one of these. In addition we're going to need aMoreThe bill of $15 at scrap price and pick yourself up one of these. In addition we're going to need a welder and some sort of oxy-acetylene. Or plasma capability for any cutting we might need to do.
How do I identify a Peter Wright Post vise?
2:168:41Peter Wright, Blacksmith Leg or Post Vise - YouTubeYouTubeStart of suggested clipEnd of suggested clipDevices you see a real long leg on it. And what that was I don't have it done yet here. But theMoreDevices you see a real long leg on it. And what that was I don't have it done yet here. But the bottom of that leg was anchored at either the bottom of the post. If it was mounted on a post.
What is Pipe vice?
Definition of pipe vise : a vise shaped to hold pipe for threading, cutting, or reaming.
What is a vise?
A vise (American English i.e. not really English at all) or vice (English) is a mechanical apparatus used to secure an object to allow work to be performed on it . Vices have two ...
Which side of the bench to mount a leg vise?
Since I'm (mostly) right-handed, I'll be mounting the vise to the front-left leg to make edge planing easier, but if you're left-handed you may want to consider mounting it to the front-right leg.
How to keep a rod perpendicular to the leg?
The solution was to simply use a piece of wood as a guide to help keep the rod perpendicular to the leg face. To do this, I removed the shelf and since I'd already glued the inner stretcher in place, I drilled a couple of holes through it and then attached the guide with screws to the outer stretcher.
Can you clamp a linear bearing?
With both of these changes, it's now possible to apply a large amount of clamping pressure to a work-piece without fear of damaging the linear bearing. So far I've been really happy with the way it turned out and how well it works. Next up will be a sliding dead-man which should make it even more useful!
What is a leg vise?
The Leg Vise handle is attached to the shaft with a quick release pin which allows the jaw to be removed entirely in seconds. The pin system also allows you to select either a wooden hub and handle or a metal hand wheel to customize your vise. The hand wheel or wooden hub is sold separately to allow the consumer to fully customize the vise.
How to install a VX 20?
The VX 20 is simply installed by drilling holes through the bench leg or apron and mounting with wood screws. A Delrin bearing is screwed into a counter-bored hole in the front of the bench leg or apron and supports the weight of the vise jaw.
What is the best way to lubricate a clamp shaft?
Lubrication: The clamp shaft may be lubricated if desired. Paste wax is recommended to keep work piece from being soiled. The internal mechanism is lubricated with grease.
What is a vise in woodworking?
A woodworking vise, according to its dictionary definition, consists of two jaws for holding work and a mechanism, usually a screw device, that opens and closes those jaws. That’s a rather broad definition, but then vises are a rather diverse lot. For convenience, vises are loosely categorized by the position on the woodworking bench they usually ...
What are the parts of a vise?
The vise’s constituent parts include a pair of iron jaws, while its other components—its slides, drive, screw, and handle—are usually steel. Like wooden face vises, the inner jaw is fixed, while the outer jaw is operated by turning the handle centered on the front of the tool. Clockwise motion will tighten the screw mechanism, ...
What is the end vise on a bench?
Built into the end of a bench (almost always the right-hand end), the end or tail vise, as it is also called, can be used to clamp workpieces to the bench between its jaws. The flush-mounted end vise uses the benchtop as the inside jaw, and the bench screw drives the movable jaw tight against it.
What is the clockwise motion on a bench?
These vises are usually located over or near a leg (to avoid putting unnecessary force on the benchtop ) and are fastened with lag screws or carriage bolts.
Where are the vises on a woodworking bench?
Woodworker’s vises are designed to be attached to the underside of the front of a woodworking bench. The vise’s constituent parts include a pair ...
How wide is a woodworker's vise?
Woodworker’s vises come in almost any size, with jaws ranging from six inches wide to ten inches or more, with a maximum opening capacity ranging from roughly four to as many as fifteen or more inches. The size you need depends upon the size of the stock you will be likely to use for most of your projects. Advertisement.
What is a dog hole in a vise?
It is distinguished from other vises in that a rectangular hole is cut into its top, and that hole is aligned with a series of other holes along the front of the benchtop. A workpiece to be shaped or cut is set along the front of the bench, flush to a bench dog set into the “dog-hole” in the vise.
Can a metal vise be retrofitted?
And it also seems as if you need to plan the whoile workbench around a leg vise. A metal vise, on the other hand, can be easily retrofitted or incorparated on most any workbench.
Does a vise work better on heavy chisel work?
It also holds work better for heavy chisel work, slip a block under the leg, makes for a much more solid hold then the regular vise. Tedstor.
What are the advantages of using a vice?
One advantage of using this vice is that having fastened the job once, we can revolve the job in any direction for doing different operations like filing, chipping, etc. It saves time. This vice has been shown in the figure.
How many types of vices are there?
Vises: 15 Types of Vice - How to Use? [Picutures &PDF]
What is a cast iron vice made of?
The complete construction of this vice is made of cast iron. Both its jaws are made of tool steel. The spindle handle is made of mild steel. This vice is most widely used in a workshop.
What is the mechanical device used for holding jobs called?
The mechanical device used for holding jobs is called vice. Also, it can be said that a workshop is incomplete without a vice.
Is a V-shaped jaw a vice?
It is a very useful vice. In this vice under both the parallel Jaws “V” shaped jaws are also made. Thus, along with the flat job, round pipes and rods etc. can be easily held, It has been shown in Figure.
Can a hand vice be used as a bench vice?
The combination hand vice has been shown in Figure. It can be used both in the form of a small bench vice and hand vice. By holding its vice handle it can be used as a hand vice. A base clamp is provided with it. With this clamp, it can be fitted on the bench also. In this way, it functions as a small bench vice.
Can a spring loaye be fitted on a work bench?
It cannot be fitted on a work bench. As per its name, it is held in hand. Instead of handle a wing nut is used which is attached on the spindle fixed between the two jaws. Between the two legs a spring loaye is fixed because of this it opens easily.
