Make a Bench Vise for Woodworking
- What You Need. About 16 linear feet of one by six hardwood (actual measurements ¾” x 5½”). ...
- Front Jaw. Cut two 32” long pieces from the one by six board. ...
- Rear Jaw. The rear jaw is L-shaped. The short ‘lip’ is used to clamp the rear jaw to your workbench. ...
- Drill Holes for the Hex Bolts. Drill two ½” holes through the front jaw 3” from the short edge and 2 ¼” from the top edge. ...
- Make Handles. You could stop right here and use ½” hex bolts and washers to complete the vise and open/close it with a wrench.
- Use Your Bench Vise. I did not use any finish on the bench vise or handles. I plan to sand it down if it needs cleaning. ...
Full Answer
How to use a DIY woodworking vise?
DIY Woodworking Vise Step 1: Welding a Nut to a Base. I want to use a M16 threaded rod for the linear movement. Therefore I need a nut or... Step 2: Welding a T-Piece, a Washer and the Rod. I want to use a T-piece pipe to hold the threaded rod and a wooden rod... Step 3: First Test Run. Both parts ...
What kind of vise do you use for a benchtop?
End vise Essentially a large face vise, this type usually spans most, if not all, of the benchtop’s width [ Photo J ]. Typically, you use two rows of bench dogs to hold long or wide stock. The timing chain on a twin-screw end vise syncs the screws.
How to turn the rod of the vise?
Now you can turn the rod by turning the T-piece. The washer we added is very important. It will later hold the jaw of the vise and will make it move when you want to open the vise. Be careful by welding zinc-coated material! Acrid fumes can be developed! Both parts are finished. Let's try if everything fits together. Looks very good.
How do you attach a vise to a table saw?
Use a screw gun and three-inch deck screws to fasten the base of the vise to the back-bottom side of the back jaw of the vise. Screw through the front of the back jaw into the base of the vise. Space the screws evenly every 6 inches. Place the base of the vise onto the edge of the vise mounting surface.
How do you make a bench wood vise?
0:306:39DIY Woodworking Bench Vise - Quick and Easy Shop Project - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo let's get. Started. Over at the table saw i cut a piece of 1 inch thick ash to 5 inches wide forMoreSo let's get. Started. Over at the table saw i cut a piece of 1 inch thick ash to 5 inches wide for the face of the vise.
How do you make a homemade wooden vise?
0:167:17How to make a Workbench Vise ( DIY MOXON VISE ) - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn one side of the jaw. I need to round out a dado slab. This will need to be equal to the thicknessMoreOn one side of the jaw. I need to round out a dado slab. This will need to be equal to the thickness of the plywood that will be used for the base the prow what I'm using is a bit thinner than 3/4.
What kind of wood is used for bench vices?
You can use plywood, a good grade, or solid wood, even pine, if that's what you have, to line the jaws of your vise. In this case I've chosen sapele, an african hardwood with perfect hardness and compression for this work. I've used it before and it's one of the best.
How thick should wood be for vise?
I would recommend at least one inch of hardwood onm the outside face of the chop. The inside face need not be as thick since it will not be compressed during tightening, so about 1/2" should do it.
How do you end a woodworking vise?
0:406:26DIY - Fast Action Vise for Woodworking - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo this is a quick look at the Vice in action before we get started here you simply push that buttonMoreSo this is a quick look at the Vice in action before we get started here you simply push that button you can push the the little clamping piece down to wherever you want it and then turn the knob.
What can I use instead of a vise?
Cut out this bird's mouth shape using whatever you have: a back saw, jig saw, coping saw, band saw. Set up the long piece of wood as a stop against the end your worksurface. If you're right handed, that's the left side; if you're a leftie, then the right side. Clamp or screw it in place.
How do you protect wood in a vise?
0:151:08How to Prevent a Workshop Vice from Damaging Wood - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust put it in place crank. It down I matter how much pressure you put on this. You're going to haveMoreJust put it in place crank. It down I matter how much pressure you put on this. You're going to have those pads in place.
How do you make wood vise jaws?
0:215:35Making New Vice Jaws - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's a hardwood. So it'll be nice and durable the jaws on my other vise they were just made fromMoreIt's a hardwood. So it'll be nice and durable the jaws on my other vise they were just made from some block board which is laminated pieces of pine with a veneer on both faces.
What is normal workbench height?
34″ – 36″34″ – 36″ (86cm – 91cm) tend to be the most common workbench height for woodworking. A height in between these two extremes tends to be the most popular, particular if you do a range of activities at your workbench.
How thick should wood be for bench?
Remember when you purchase wood add a minimum 3-5 inches to the length, 1/2-1 inch to the width and a minimum1/4-inch to the thickness. Should you decide on a bench that is longer than 36 inches, you will need to calculate how long your aprons should be.
Is Birch a good wood for a workbench?
These are heavy-duty, solid European Birch tops which are perfect for use in your shop or home. They can be the basis for making your own custom workbench or a butcher block counter on an island or a coffee table. Birch is a hard-wearing durable material for any top and gives a natural look to any project.
What is the best top for a workbench?
The Best plywood's for workbench tops The best one to use is Baltic Birch or marine grade plywood. You want to use 3/4 inch or thicker sheets of plywood for stability and strength of your work surface.
How do you make a wooden screw vise?
10:4013:26How to Make a Leg Vise With A Wooden Screw All Hand ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd give it a nice clean look and feel I put in one screw. Into each hole. So there are two screwsMoreAnd give it a nice clean look and feel I put in one screw. Into each hole. So there are two screws in each plate. And can then go around the main screw of the vise.
How do you make a vice clamp?
1:107:296 homemade clamps and workbench vises - YouTubeYouTubeStart of suggested clipEnd of suggested clipThese are just a couple of strips with two bolts. I put the work pieces between the strips. AndMoreThese are just a couple of strips with two bolts. I put the work pieces between the strips. And there are a lot of holes all along both strips.
How do you make a Moxon vise?
0:0815:06$40 Moxon Vise - Easy to build in an afternoon! - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis kit comes with everything that you need to build a quality Moxon vise it also comes with a setMoreThis kit comes with everything that you need to build a quality Moxon vise it also comes with a set of instructions.
What is a face vise?
Face vises are designed specifically for holding wooden workpieces while such operations as drilling and sawing are performed. The traditional material is wood. A wood face vise consists of a movable front jaw that is mounted to a broad, square beam that slides in and out of a matching channel.
How long is a 5/8 copper rod?
I use two 5/8" copper pipes to support the rod and to keep the jaw from rotating. They have a length of 50cm. You can adjust the length to your needs.
How to fix a rod on a nut?
To fix the rod, we added a small hole through the T-piece and the rod and insert a small bolt. Now you can turn the rod by turning the T-piece.
Is maple wood good for a work bench?
very nice. The only problem I have is you should have used hardwoods for maximum durability. Some maple would not have been too costly. Over time you will find these things matter in a work bench. It really gets beat up and a soft wood will not endure as much abuse.
Do you need clearance for horizontal movement?
Well you need some clearance for the horizontal movement due to the slop of the thread. When move the jaw you’ll see that it’s slightly misaligned to the other. But that clearance is very small and is easily achieved by the holes where the pipes go into. I used the copper pipes because they were scrap material from an old project and were laying around in my shop. I guess you could easily use different kind of pipes, hollow or solid, of different materials. Take what suites you is the cheapest.
Step 1: The Plan
Back in April, I tried to build a vise, but it didn't really work out like what I wanted. You can see that vise here.
Step 3: Cut Wood to Size (& Glue for Making the Final Size)
Since this is made from reclaimed wood, I thought there would be no point in making two different steps, for cutting, and then gluing, to the final size. For example, if this was made from a 2X4, the base wouldn't have been made from two different parts. Makes sense? :)
Step 4: Drill Holes for the Front & Back Jaws
I aligned and clamped both of the 5 X 9 X 7cm pieces one on top of another. Make sure they are totally aligned before you drill, this is REALLY important!
Step 5: Chisel Holes for the Hex-nut
The nut is going to fit inside the back jaw, like my first homemade vise, I decided to chisel out the holes. This works really well!
Step 6: Glue the Rods
I mixed up some 2 part Epoxy, and glue the rods inside of the holes that were previously drilled in the first jaw.
Step 7: Glue the Front Jaw
Glue the front jaw to the base with some wood glue. If you want to turn this into a Bar-Clamp, you won't need to do this ;)
Step 8: Make the Handle
I started by drilling a 9mm hole in the tip of the 3.5 X 4.5 X 7cm piece, and when I made sure that the rod fit snuggly inside, I drilled a 2mm hole through the wood and the rod. This will help strengthen the bond.
How to make a wood vise?
Place the 2-by-4-by-12-inch hardwood board in front of you. Measure and mark three inches from each end of the board. Use a drill and ¼-inch drill bit to drill through the board at the pencil marks. This board will form the base of the vise.
How to tighten a vise?
Slide the carriage bolts through the back side of the holes in the back jaw plate of the vise. Slide the front jaw plate onto the carriage bolts from the front side . Slide the remaining to fender washers onto each of the carriage bolts. Thread the 3/8-inch nuts onto the end of each carriage bolt. Use the 3/8-inch wrench to tighten or loosen the vise as needed when using the vise.
How to attach a vise to a mounting surface?
Place the base of the vise onto the edge of the vise mounting surface. The back jaw of the vise should hang off the edge of the surface. The base should be fully on the mounting surface. Use a ¼-inch wrench to fasten the base of the vise to the mounting surface using the ¼-inch lag bolts.
What is a vise in a shop?
A simple vise can be made from items around the shop. A vise is one of the most useful tools in the shop. It is often overlooked when thinking about outfitting the wood shop. Commercially available vises are costly and have limitations. Wooden vises on the other hand can be made by the woodworker.
What to use between the jaws of a vise?
Use cardboard or felt between the jaws of the vise when using very soft woods in the vise.